hola, como descargar software de administración (vManage) y actualización para el cisco ISR4331. llevo horas tratando de descargarlo, y si intento descargar las actualizaciones me pide un contrato nose de que. porque todo es tan engorroso :/ ayuda ...
Forum Posts
Resolved! 4221 combo AUX/Console port problem
Hello!I'm trying to config remote backup acces from Cisco 4221 to switch 2960L using router's combo aux/con port. I connected these devices with rollover cable. The router doesn't have physical aux port, but it has combo aux/console interface. Config...
Resolved! Issue with ISR4221
Hello, having IP phones connectivity issue with ISR 4221 Router, internet working fine, below is the configuration: Router(config)#do sCurrent configuration : 1752 bytes!! Last configuration change at 04:37:06 UTC Wed Jan 22 2020!version 16.5service ...
Resolved! C2960 bootup
i will try to give just the basic info. I have a c2960 switch, files were deleted from it. I copied (c2960c405ex-universalk9-mz.152-2.E9.bin) from another switch to a usb. I can get the switch to boot normal from the usb and have copied it to flash b...
Resolved! Max age of OSPF LSA's
What is the default maximum-age of a Type 1 OSPF LSA? A router with ID 222.1.6.1 is on my multiaccess segment. I was logged on to 222.1.7.1 with log-neighbor-changes enabled; I powered 222.1.6.1 down and watched the adjacency vanish; but the 222.1....
Hello,We accidently lost ios for 2960-x switch and i tried to upload new one via xmodem rommon mode. I copied new ios from other switch and also download from cisco website but in both the caseafter "boot flash:image.bin" command it ends with follwo...
Hi!How can I configure IP to MAC binding on cisco 3800 series? Thanks.
Hi AllI have been looking into vxlan.Are there many people who use it here? what are the main reasons for people using it?what switches / routers are supported?do you always have to map vni's to vlans ? could you map all your vxlan vni's over 1 vlan?...
Hello all, if you are reading this, I hope you are well. I I am trying to figure out if Cisco Catalyst switches support referencing a Named Object-Group in a Policy-Based routing statement. The GNS3 lab I am in right now running iOSv Version 15.2(4 ....
Hi AllWe seem to have an issue with object tracking on our routers running version 16.6.4When we type show standby, the objects are showing as "unknown"they are tracking the line protocol of an interface.On other routers with different software, they...
Hi, I've been working on this for 3 days and no resolution. Hopefully some smarter folks here will throw me a bone!I have a hub and spoke phase 3 topology that works great except for speed- internet speeds (DIA) are as expected, spoke is 100M and hub...
GuysI have one router with two links to two different ISPs LTE ( one ISP use rip and second one use OSPF)anyway I want to route traffic based on link quality ( RSSI strength) not routing table .how can achieve that ?
Resolved! help connecting vlans with 3 routers
hi I tried so many things like router rip, ip route etc but I cannot connect my vlans altogether it seems only vlans 10,20,30,40,50 communicate but not 60 70 80 my architecture looks like this SW1 (with vlans 10,20) ---- R1 ---- SW3 (with vlans 40,5...
Hi,I have a scenario where I have to SPAN traffic from Nexus 9K ( Source ) to Catalyst 9K ( Destination ) . As Spanning of traffic is between switches and nexus is involved it is mandatory to use ERSPAN . Please find the attached connectivity diagram...
Hello to all community,Above is a diagram of my network, we had Zywall network device then upgraded to CISCO 4221/K9, internet is working fine, but the IP Phones does not, we are using Cloud phone service, so the problem with the Router, kindly check...
