I am little confused about using the exact RegEx for route filtering. here is the BGP topology R1(IDMZ)---------ebgp 64000------FIREWALL-----ibgp 64600-----R2(EDMZ) R1 is sending default to R2 and receiving only R2 Local and its connected AS ro...
hi,just a sanity check here. we currently have a dual ISP link/router to a single ISP and the setup is via HSRP (with static default route to ISP hop). plan is to migrate to BGP with IPv4/v6 dual stack.we would like to do some POC and pre-configure t...
I recently upgraded my 2951 Router from IOS 15.4 to 15.7. Before the upgrade, I woud typedebug serial intto get the HDLC debug outputand I would get the following debug output HDLC myseq 6, mineseen 6*, yourseen 7, line up Now, after the upgrade, I ...
Hello,We have an ASR9006 in the heart of the network which supports 4 eBGP links to 4 different transits with each a fullview.Our 4 transits are very substantially identical at the AS-Path level of the routes, and therefore, in upload, only the last ...
So as I study for the CCNA, I set up a Cisco router behind my Ubiquiti home router that is connected to my DSL modem. After I configured the interfaces and default route, I was able to get out to the Internet from the router, but I could not reach t...
Refer to the attached scenario where internet router is connected to ISP using the public IP. A firewall is connected to the internet router using private IP. We need VPNs to be terminated on the Firewall so its outside interface needs to have a publ...
Hello Everyone,im practising MP-BGP on GNS3 and i configured everything.PE1 routing table============sh ip route vrf co1Routing Table: co1Codes: C - connected, S - static, R - RIP, M - mobile, B - BGPD - EIGRP, EX - EIGRP external, O - OSPF, IA - OSP...
nexus 7000Himy customer want to buy M3 module to extend 10G interface, the original Nexus 7000 have m2xl module, when i create new vdc and change moudle-type to m2xl m3, then allocate interface (m2), it show me some error message switch(config-vdc)# ...
I am trying to create a ROAS in Packet Tracer and have come up to a wall. In the attached file I can not ping the hosts of one VLAN to the other. I can ping hosts on the same VLAN and the gateway. I am really new at this and any help will be appre...
Good Day, In what scenario would you ever configure just a GRE tunnel between Branches without IPSEC (encryption)? Regards,
Hello Everyone,I have an assignment to do but due few confusion I couldn't do it properly. Can somebody help me to Finalize this topology. I have designed the topology and provided some information about my requirement. Thanks in advance,
please helpi need to go to vrf internet from global routing table in R6 need to ping 1.1.1.1 from R6 ??????????? R1!ip vrf Internetrd 65:65!interface FastEthernet0/0ip address 172.16.234.1 255.255.255.0!interface FastEthernet1/0no ip address!int...
We are using TAC_PLUS as our tacacs server and we have made changes to Tacacs server for better control so when user is in config mode he can run some commands while not execute some command we were able to achieve this on XE router by enabling "aaa ...
G'day everyone, I have an ASR 1K where I have a hierarchical Qos policy doing sub linerate shaping on the main interface based on DSCP. That is working with no problem.Now what happens if I add a sub-interface without any policy-map? Is the main shap...
Hi guys ,i just want to know why enterprises use mpls rather than using vpn over internet in their wan connections,despite Mpls connection had a higher cost than internet connection
