Hi, I have two routers set up with HSRP connected to two ISPs, one cable and one DSL, so customers can always access our DMZ should one ISP go down. The routers are connected to our trusted network, VLAN1, and our DMZ, VLAN4.But trusted network PCs g...
Forum Posts
Hello. I've got a pretty basic small network set up with a PIX 501 as the router. My inside subnet is a typical 192.168.0.0/24 setup. I received four IP addresses from my ISP (which I will list if you like), and I currently have one bound to the outs...
Good morning all,I do not have a good English so I made a diagram for you to understand me. Is it possible to obtain this? I can not find the options on my cisco rv345 router. Thanks for your help.
Attached diagram represents my network. At the Cisco 9500 core switch I have each SVI in its own VRF. I have created 2 VRF's for Internet & MPLS. I am using VRF-lite route leaking to control inter-vlan traffic at core switch level. Also using iBGP to...
Hi All, default route to internet to communicate with the private networks. ISP1s are active through AD and ISP2s are backup via IP SLA. I want to communicate to the AMERICA's server via ASIA's ISP2. When I do a basic static route, everything works f...
Hello. We have an ISR 4331/K9 with voice and security license on them. A show inventory shows our NIM card installed: "NAME: "NIM subslot 0/2", DESCR: "NIM-2MFT-T1/E1 - T1/E1 Serial Module"PID: NIM-2MFT-T1/E1 , VID: V05 , SN: FOC23354FUE" I've config...
Hello,I have 2 questions about Cisco 1921 router:1- Does Cisco 1921 router supports RIP protocol? (I searched for its datasheet (https://www.cisco.com/c/en/us/products/collateral/routers/1900-series-integrated-services-routers-isr/data_sheet_c78-5983...
I have a Cisco 2911 router with the UC license running IOS c2900-universalk9-mz.SPA.157-3.M.bin and a SM-ES2-24-P switch installed into it with 5 IP phones connected to the switch. Please note that this is a Service Module switch and not an external ...
Resolved! Protecting against DDOS attacks
I have a Cisco 2901 router configured to allow access to a DVR device using NAT and ACLs from the Internet. I can't lock down the ACLs to a source IP due the customer's DRV app needing to access the DVR from anywhere out on the Internet. I see port ...
Hi, I'm trying to configure PIM Bidir on a Cat6509 running the s2t54-adventerprisek9-mz.SPA.151-2.SY8.bin image, but I don't see the bidir option when configuring the rp address. Looking at the Cisco Feature Navigator, this image supports Bidirection...
Dear Team, I have one ISR 4331 having only Lan two ports ..We are now in phase of SdWan implementation...I have two SD wan devices at site..But I would like to only one gateway for these two SD wan devices which is going to connect router... Option1:...
Hello, You can see my topology on the file picture. I will say i am a beginner and i want to make a site-to-site VPN with two Cisco ASA (Active/standby) using Failover. The NAT will be done on Firewalls I need also to keep a redundant gateway for my...
how do we restrict a router interfaces from directly connected to Some vlans? can any one help me to figureout?the question is Router should not have interfaces directly connected to Vlan 30 and Vlan 40
Hello, I want to install RV325 to use dual wan with Bell home hub 3000, I plan to use Bell home hub 3000 like DHCP server and wifi, and use RV 325 like a switch. Bell Hub has 192.168.2.1 ip adress 192.168.2.1 I tried to install RV325, changed ip to 1...
I have a Cisco Catalyst 3560-CX switch and an RV320 router.I am trying to configure my router only for VPN and the switch in layer 3, I have 3 Vlan: Vlan 2 (wireless data), vlan 3 (VoIP server) and Vlan 4 (NAS and web server), but I still can't ping ...
