On R2 route map in permit 20it permits the route that was denied in deny 10:!interface Ethernet0/3no ip addressshutdown!!router eigrp 1distribute-list route-map FILTER_IN innetwork 192.168.0.0 0.0.255.255network 192.168.12.0!ip forward-protocol nd!!...
HiWhat book would you recommend for 350-401?In the past I had used the Cisco Official cert guide and although useful it can be a bit 'dry'.I also have an active susbcription to CBT Nuggets which I will be using. CheersLassek
Hello Community,I always had a question how server determines at which network speed it can send traffic? I mean, for example some user in Australia wants to download file from server in Canada, there are a lot of links with different network bandwid...
So first of all apologies for this unconventional design. Apparently a R&D team didn't think of consulting network team before procuring the devices and we ended up with this and have to make it work. The issue is: I am getting internet on Server1 b...
ip sla 1icmp-echo 119.29.29.29 source-interface Vlan2verify-datafrequency 30ip sla schedule 1 life forever start-time nowip sla 2icmp-echo 223.5.5.5 source-interface Vlan2verify-datafrequency 30ip sla schedule 2 life forever start-time now ip route 1...
I have an ISR 4331. I have to restart often because users can't load pages.The show int g0/0/1 command on the LAN interface configured with virtual interfaces indicate massive packet drops.
Hello everyone, I am currently working on an MPLS VPN project with the goal of virtualizing multiple network infrastructures and enabling communication through an MPLS VPN. My CE devices have no issues communicating with each other, and the WAN inte...
Thanks for any help guys. This is probably a dumb question but I can't seem to get it working...I have an 8300 router with an 8-port layer 2 module. I have a layer 3 port set up with multiple subinterfaces as a trunk that goes to a switch in another ...
Fibre cable (media converter to ethernet) connect to Cisco 4200 seriesrouter> router>en router#config t router(config)# router(config)#int gi0/0/0 router(config-if)...
Dear Concern, I face some issue for replace my switch. Here i share some log. LOG:2020 Dec 31 03:49:55 cisco-9000 %L2FM-2-L2FM_MAC_FLAP_DISABLE_LEARN: Disabling learning in vlan 1949 for 120s due to too many mac moves sh mac address-table notificat...
Hi Guys, I'm trying to config macsec between cisco 4500 and AWS. On the 4500 it's seems that i don't have all commands. like under mka policy, i dont have macsec-chiper-suite or key-server... Software: cat4500e-UNIVERSALK9-M Version 03.08.01.E with e...
Hello Tech Team, I have a challenge with my lab simulation. I have created multi homed BGP Network. I'm running BGP routing protocol in all routers ( Internet source, Two ISP Routers and two campus internet edge router on HSRP. HSRP is working perfec...
I've inherited some ISR4431 and ISR4331 routers with ROMMON 16.12(2r). I checked the release notes and saw this was recommended prior to upgrading to 17.6.x.16.12.x => 17.6.5aI want to upgrade to this version first before going to 17.9.x train (since...
Hey guys, hoping to get some insight on the best way to address my failover issues at a current location.We have two ISP’s, one is primary WAN1 and other is WAN2 as a backup in case WAN1 goes down. Internet fails over perfectly fine, but our VOIP sys...
Hi All,i have a network setup where i need to redirect specific IP range to another.a brief overview of the network, i have a router that connects via VPN to the company network. Now i have a local network with address 192.168.0.x that i need to rout...
