Resolved! Why can't the hosts ping each other?
.pkt file is attachedI simply cannot figure this out, help!
Forum Posts
Resolved! VRF and ARP table memory utilization
Hi Community, Recently I've been involved in a proyect that requires the usage of VRF and MP-BGP. Here's my doubt:SWITCH_A has two VRF (Red and Blue), those VRFs have assigned the VLANS 100 and 200 respectively VLAN 100 subnet is 192.168.100.0/24, VL...
Resolved! Cisco GETVPN over MPLS Issue
I have 2 sites connected over MPLS. R1 is the CE router (Network: 10.0.0.0/8) R2 is the PE router in SITE-1 (Using network: 192.168.0.0/16 and 172.16.0.0/16 R7 is PE the router in SITE-2 (Using network: 192.168.0.0/16 and 172.16.0.0/16) R9 is the CE ...
We are migrating our global wan core routers from Juniper to Cisco. We have extensive and complex policy based TE configurations. One of the Juniper BGP policy statements uses the local-preference add # option. I cannot seem to find an equivalent rou...
Here's the scenario: I have 2 separate corporate sites, Site A and Site B, that each have their own internet connection and use a static default route to reach the ASA. These 2 sites plus 4 additional branch sites make up the total network. All sit...
Resolved! What set metric command does in RIPv2
Hello guysI've been working on some project in Cisco Packet tracer for last few days.I build my network,set every addresses and conections between routers etc.Today I started dealing with metrics (Im using RIPv2 protocol in all routers) and I got a b...
Resolved! EIGRP routing issue
First, the topography: (ISP Router) [10.0.0.1] < (VLAN 221) > [All VLANs have IPs in their respective subnets and DHCP] (3750 Switch w/IP Routing) < (TRUNK) > (3750g no routing) < (VLAN 323) > Host I have EIGRP enabled and as you can see in the outpu...
I have a Cisco 1921 Router. This router is a Transit router between my internal network and a clients network. I have a BGP partnership on both sides. My network is on GE 0/0 and my clients network is on GE 0/1. I need a 1 to 1 NAT across this router...
ISR 4321 cannot SSH into any other router. please help. thanks.
Hi Tech Guys, We have requirment to use 4 Core switches and 2 Distribtuion switches in a campus network . anyboday know about this type of deployment in large enterprise. Pleae share any article or document related to this type of implementation.i di...
Hello everyone! I need help to set up my IPSec VPN. Here is my topology in GNS3: I'm trying to setup a VPN between ffw.par.rt01 and each of the other router (mar,lim,nan). Meaning every VPCS can access the ffw.par.* VPCS via the VPN, and the ffw.par...
I've attached my network diagram, but here is my problem: R1 only uses EIGRP protocolR3 only uses OSPF protocolR2 and R4 only use static routesR0 will redistribute all the routes it learned. Right now, my main problem is that I can't even ping from L...
Hi, I am having brain fog and wanted to know what is the best way to setup routing between two sites that are connected via a 3rd party managed LAN extension.The 3rd party is configuring all the site to site connectivity through their NTE and will pl...
hello. I'm newbie network engineer. nice to meet you everybody. I have a question while reading Cisco catalog. Can EIGRP Stub work without EIGRP protocol? I don't know what this means. I know it's a weird question, but I'd appreciate it if anyone cou...
I have the below scenario Loc A Loc B Loc CRouter A -> Router B -> Router C I have 3 locations as shown above Location A is connected to Location B & Location B is connected to Location CAll are running OSPF. I want to achieve th...
