Hello.first of all, I hope this is the right place for my post. I'm somewhat new in the cisco world I was introduced to Cisco equipment and non-GUI configuration of switches/routers around 6 months ago so I hope you all can bear with a lack in my kno...
Forum Posts
Resolved! Unable to route over the ATM Interface
Hi, I have very old Cisco router (878) . It ATM port is Up and working. I want to route site B to A.so I set 1.1.1.1 on site A router and set 1.1.1.2 on site B router ATM interface. on site B router I can see remote network. can ping any host on remo...
Resolved! vrrp and multi-home isp with redundancy
we have two isp connections as of now, but now we want to implement vrrp with two cisco devices and also terminate isp links to individual ha routers. eg: isp a link to two cisco and isp b to two cisco routers. can someone explain how to achieve this...
Hello Community, I wanted to know what is the maximum number of VRF instance and the number of routes per VRF instance can a ISR4451 with 2GB of data plane memory and 4GB of control/services plane mem. im looking for the same info as presented on a...
Hello All, I have Cisco 892 router using a pppoe dialer and would like to allow pings to the interface for monitoring by ISP.Could you provide guidance how configure sameBelow is my wan interface Interface Dialer2 ip address 10.192.252.4 255.255.25...
Resolved! Cisco ASA missing BGP route
Hi, After configuring BGP on an ASA 5585-x no routes to peer are displayed with show bgp route. Below are some configs and shows Many thanks in advance. CheersGeoff sh run routeroute outside 0.0.0.0 0.0.0.0 xx.xxx.xxx.xxx 1route BGP-LINK 0.0.0.0 0.0....
Hi Team, We have configured natting at ASR but not working and Configuration(ASR,ASA,Nexus) attached for your reference and do the needful.details as below: Traffic Flow: ASR---->ASA Firewall---->Nexus switch---->Private IP Private IP...
Hi Team, We have configured natting at ASR but not working and Configuration(ASR,ASA,Nexus) attached for your reference and do the needful.details as below: Traffic Flow: ASR---->ASA Firewall---->Nexus switch---->Private IP Private IP...
Hello experts I have two hubs at HQ and have 6 spokes. 5 spokes working fine with but one spoke is having problem with Tunnels.Issue: Tunnels are active few hours and then offline fore few hours !!! What could be the reason ? Thanks in advance
Hi Friends, in the past we have used a C899G-LTE-GA-K9 , with a 15.5(3)M2 and a AME: "Modem 0 on Cellular0", DESCR: "Sierra Wireless MC7304 4G-GA"PID: MC7304 . Now we switched to a ISR4431/K9 with a isr4400-universalk9.03.16.02.S.155-3.S2 and a "Mode...
Hi Need help on Nexus 3KI am trying to use PIM in nexus 3k. everything is perfect receiving multicast but not crossing 1Mbps due to that streaming is getting stocked/scratches are there. when I am removing routing and forwarding through normal switch...
Route filtering passive interfaceCisco IOS provides several ways to control updates traffic. Passive interface, distribute list, prefix list route maps. In this section we take look at passive interface in RIPv2, EIGRP, and OSPF.Passive interface co...
HI guys, I am setup a VPN with another site, the VPN is working but we have problem to connect the pcs through this VPN. My local network is 192.168.0.0/24 and the local group of the VPN is 172.29.0.13/32. The question is how can I connect the PCS th...
VPNHi everyone, and sorry for my poor English :) .We try to connect our office to an IPSec vpn, but we encounter some issues with that. Phase 1 and Phase 2 seems to be OK, the tunnel looks UP, but there is no traffic nor ping between the remote ip ho...
Hello Experts, @Richard Burts @Peter Paluch @Joseph W. Doherty @Julio E. Moisa @paul driver I have question, We have four sites connected with each other through MPLS circuit. We are advertising our subnets by using ospf and I want to use DMVPN a...
| User | Count |
|---|---|
| 12 | |
| 12 | |
| 7 | |
| 7 | |
| 5 |
