Hello, I'm currently configuring a site. They have isp that uses a radio link. I been having issues when the internal networks reach out to the internet that they are super laggy and slow speeds. Has any configure a site that instead of having a actu...
Forum Posts
I'm trying to configure a HWIC-16A as a terminal server without success. I can get a telnet session to connect, but I simply get a blank screen, no data appears to be sent or received over the serial line.The only similar post I could find was https:...
Hello all, On Border Edges(DC01-BE001-6/7) am trying to advertise default route from GRT to MPBGP-EVPN but not able to do it properly with the following configruration. Thanks in advance for tips and correction **************************************...
Hi GuysI need to purchase 2 routers for a large site, the site will have up to a 1Gig MPLS linked to each of the routers.I was looking at the C8300-1N1S-6T, however the later series has appeared to come out, the alternative model was the C8235-E-G2Th...
i have had the system i have in place for some time and had no problems, when using a 2 router approach [isp1 and isp2] but since i merged both onto 1 device, ISRC111 there is an issue with incoming connections via isp1. i am using the same acl's and...
Resolved! OSPFv3 Interface ID
Hello, everyone. I understand that OSPFv3 separates links from prefixes and purposely moves the prefix information from T1/T2 LSAs into T8/T9. The RFC states the following: o The Hello packet now contains no address information at all. Rather,...
Hi, I have 4 multicast sources sending traffic each to two multicast groups, as follows: 10.65.190.1 -> 224.64.64.110.65.190.1 -> 224.64.64.510.65.190.2 -> 224.64.64.110.65.190.2 -> 224.64.64.5 The traffic enters the router via a VLAN interface con...
Resolved! OSPFv3 Type 8 LSA Purpose
Hello, everyone. Why are link-local addresses that are used for next hops advertised in type 8 LSAs? Doesn't the router already know them considering that they are used to form the OSPFv3 adjacency? Thank youDavid
Anyone is preparing ccie service provider lab. I am looking for group where we can collaborate our study discussion so we can exchange our concepts and it helps definitely to boost preparation.Keep learning...
Dear All , After having the old faithful 5515 on guard I am trying to migrate to a vFMC with a NGFW. Many issues arise with S2S and bugs in the GUI , BUT I am experiencing an other issue with a simple port forwarding. I have the same ACL - source out...
Hi Community,I have added the SFP module "SFP-10G-SR-S" to my C8355-G2 router,however when i tried to setup the ip address on it it does not give me ip address command. I tried to make that port with layer using no switchport command but still no luc...
Hi i have this pathAdvertised path-id 1Path type: external, path is valid, is best path, no labeled nexthop, in ribAS-Path: 208555 , path sourced external to AS172.18.14.238 (metric 0) from 185.217.6.34 (192.168.20.1)Origin incomplete, MED not set, l...
I learned that MED is applied to outbound updates , dictating the best inbound traffic into the AS, but I saw the vice-versa is also true like you can apply med for indbound updates also and it works the same right??
Hi , am trying to advertise default Mgmt-Vrf route to GRT so that other devices reachable to default route . thanks for tips and tricks . Configuration is mentioned below . DC01-leaf03-55#show run int giga0/0interface GigabitEthernet0/0vrf forwardin...
I desire to setup multiple parallel GREoIPSec connections from a single router WAN interface IP to multiple remote sites. I know that I can achieve this by applying to the interface a crypto map that is defined in multiples with different sequence nu...
