We configured ISE to authenticate and authorized our SDWAN controllers successfully using AD as the identity source. Now we are having a problem with our C8500s and vEdges and ISE/AD. The C8500s are configure for TACACS through the AAA Feature Templa...
Forum Posts
Resolved! NAT-traversel and server STUN vBond
Helloi want to knwo what's mean NAT-traversel for vBond ? ans also wha'ts mean server STUN for v Bond ? i wait a reply from expert SD-wan cisco Thanks
Hi GuysI am troubleshooting NTP connectivity and a sync failure using TCPDUMP. When I run the tcpdump interface X/X options "dst ip X.X.X.X" or tcpdump vpn X options "dst ip X.X.X.X", I don't see any traffic being sent out to the NTP Server. The TCPD...
Resolved! SD-WAN AVC portal
I enabled AVC on vManage and i see it is enabled and running thru cli, but I can't access AVC portal thru https://<vmanage_ip>:8443 It opens vmanage gui not AVC portal Is the portal still available? i am running software version 20.9.3 in multitenan...
Resolved! Wrong BGP AS-PATH in the routing table
Hello Experts, I have been looking into this long enough and need help. See below. chr-r1 is advertising shorter AS-PATH. However, the lab router is showing 2611:6bC0:6000::/40 as the same length. Any idea? lab-r1#sh ipv route vrf 13 2611:6bC0...
Hi.I have deployed vManage 20.7.1 on vmware esxi and applied basic configurations. After that I connect to web GUI by my browser and I try to login but it's like an endless loop and after click on login button, login page is loaded again.
We recently upgraded our Cisco SDWAN devices to 12.12.2 for controllers and 17.12.2(ED) for C8500/8000v. When attaching new templates and pushing new configs the following error appears in the logs:“Failed to obtain exclusive access to the IOS parser...
I have been looking all over for specifications or recommended deployment configurations for the C8000V. Looking for a document that might talk to recommended vCPU, vRAM, vDisk for the C8000V based upon the expected throughput loads. I see that we ...
Folks I am here again for your valuble suggestions.We have Branches and Big sites. As more and more applications hosting in the cloud and all the data heavy Applications like Webex and Teams needs internet. How do you accomplish Maximum uptime and le...
Resolved! vEdge authentication
Assumption: to receive a device certificate, the (virtual) vEdge generates a CSR to a vManage of a fabric.Doesn't the vEdge find the vManage through the vBond? Are unverified vEdges able to find the vManage of a fabric before the vBond of the fabric ...
What is the purpose of using preference inside tloc list?and can we see the changing on the cEdge? In almost cases I use preference via topology policy and I can see it through command sh sdwan omp routes and nevere use preference inside tloc list
Can I build L2 channel by using sdwan devices? maybe as l2tvp3 (xconnect) tunnel between two sites?
today ,when we tried to terminate 500 Mbps internet link of primary Vedge 1000 then we got reply that---this link will not work as V1000 has bandwidth limitation of 250 Mbps .May I know what is this bandwidth limitation concept in cisco ?please share...
Dear Cisco Community, Consider the SD-WAN Topology diagram attached here. I need to configure reachability end-to-end between the referred locations. Basically, in site-id 10, it has service VPN 10, and on the other side, on site 20, it has VPN 20. I...
I am using vManage version 20.9.3.2. By default when the vManage CPU utilization increase by certain % it is considered as Critical & it is shown in the dashboard.I would like to understand the below.1. What is the default % which is defined as crit...
