In the Cisco SD-WAN Bulk API, which Stats endpoint would contain the latency, packet loss, and jitter for the WAN interfaces, so I can track the underlay network health for each Intranet Provider? I see these for tunnels, but not for interfaces. T...
Forum Posts
The client vpn I set up on our MX95 is no longer connecting from either my windows 11 laptop or my home windows 11 pc. it previously was working properly. the connection was set up with L2TP and a preshared key. On either client i get "The connection...
With dynamic site to site enabled, the health dashboard will show Partial WAN Connectivity for all sites if one site goes down. Is there a way to only have the dashboard show the health toward the hub routers? While the data is a true representatio...
Resolved! TLOC-Extension Not Working?
My setup is two cEdges running VRRP. In my scenario,cEdge01 is Master and has two ISPs connected to it. cEdge02 is Standby and has one ISP connected to it. Each TLOC-X has it's one cable, so three cables connecting between the cEdges. All vManaged. O...
Hello everyone I`m doing a SD-WAN lab on Pnetlab on Vmware Esxi And my problem is when I want to generate CSR for vManage to sign it in the certification authority in Windows Server,I`m getting fail.According to pictures I use Enterprise root certi...
Hi there. I wanted to set up a cisco SD-WAN topology in eve-ng. In my first try i got to install all the certificates for vManage, vBond and vSmart successfully, but realized that i had to change the organization name of my controllers so that it mat...
Hello, i am seeing weird behaviuor not sure if others are facing same.I have configured tacacs servers in template on vmanage as below.. 192.168.30.10 port 49 key xxxx192.168.20.10 port 49 key xxx192.168.10.10 port 49 key xxxThis templa...
Hi There,When i am trying to access the vManage from Google Chrome Browser its not accessible, giving error "This Site Can't be Reached". However, CLI mode is properly accessible from Putty.Ping is successful from both end Windows CMD side & vManage ...
Hi All. I have Catalyst 8000v (iOS 17.6.3a) running on AWS instance and I need to create GRE tunnel to AWS Transit Gateway for redundancy reason. I use CLI template because as I check on vManage 20.6.3 there is no GRE template configuration available...
Hi I need to know in case of failover from primary to secondary vSmart node. What would be the behavior If primary vSmart would comeup , would it be remain on secondary node or it will come back to primary node. Does these controller support Preempt....
Resolved! SDWAN cEdge VRRP flapping
HI expertsThere is a problem of cedge vrrp,the configuration as below.Master device: Current configuration : 255 bytes ! interface GigabitEthernet4.101 encapsulation dot1Q 101 vrf forwarding 1 ip address 172.16.101.252 255.255.255.0 ip mtu 1496 ...
Resolved! SD-WAN new
Hi Friends I am start learn some topic about the SD-WAN I read about vedge, cedge, vmange and vbond vsmart and know dtls and Ipsec/gre tunnel OMP and TLOC. DAI and NATing and routing between VPNx. all above I know I need more info. about SD-WAN can s...
Resolved! maximum count of secondary regions
Based on SW version is maximum number of regions 8 or 12 (I'm not sure, but I think, it's connected to PRIMARY regions). My question is, how many SECONDARY regions can I use? Is there any limit (no there is no info in documentation)? Another question...
I am trying to manually on-board a CSR router (IOS-XE 16.12.3)I am running my controllers (18.4.3) on premise (proof of concept lab).The certificate gets installed by Vmanage on the CSR but vBond refuses to authenticate the connection from the CSR: ...
Hi I do have some queries related to DR deployment in AWS cloud .I have gone through the Cisco documents for Vmanage DR deployment, and all the documents mentioned the cluster formation to achieve DRMy requirement is I want to keep standalone node in...
