I changed system-ip, but I can't change it to Valid.The following message is displayed. ErrorerrorFailed to save vEdge list10.1.1.6 already exists for vEdge-C1111-8PLTELA-XXXXXXXXXX (host name)How can I change it?
Forum Posts
Is there a way to see when a Edge device was changed from Vmanage mode to CLI mode and what template was being used?
Is there a CLI command that will show me the same ouput as below in vmanage when checking the control connections of vedge routers.vSmart Control Connections (Expected: 4 | Actual: 2 ) sh control summary - just displays the current up/connected conn...
Resolved! SDWAN DTLS Connections
When I remove tunnel interface of vManage or vSmart DTLS connection is down.DTLS connection only form when I recreate the tunnel interface on vManage or vSmart.Please help me to understand why it behave like that? what is the requirement to have tunn...
Hi Team; Our service VPN routing table includes 1000s of prefixes which leads to huge slowness in retreiving this table data via external tools and I would like to show the complete routing table without breaks for my vEdges and cEdges? I'm looking f...
Resolved! encapsulation ipsec on vBond ?
Hi all, I have a question regarding configuring a vEdge as a vBond... I was following this Cisco Live document on how to create a SDWAN home lab https://www.ciscolive.com/c/dam/r/ciscolive/emea/docs/2020/pdf/LTRRST-2734-LG.pdf On page 27 it says you ...
I have an MX64 that has (very intermittent) connectivity issues with the outside world. It can be anywhere from 4 minutes to 15 minutes and it can happen 3 times in a day or once in a week. When I check the event logs I see 'Ethernet port carrier cha...
Hi expert guysI just install EVE-COMM-VM-112 free version on VMware Esxi 6.5.0. All done and I tried setup lab with viptela OS v 19.2.4 and 20.3.4.vedge & vmanage are working well, but for vbond and vsmart I can not set initial password:After it show...
HI there While I can log into vManage using the web browser, I am unable to authenticate to it via the REST APIs. This is happening whether I use Python or POSTman. I used respective credentials provided for both the always-on (shared) and reserved (...
Hi All.I am planning to deploy ISR 4k as cEdge. As I plan a cEdge to have redundant VPN 1 connection to a stacked distribution switch. Is it posible to configure port-channel on this environment? Thank you.Best regards,
Hi,I am creating a Service VPN feature template with VPN number as a variable. This feature is not supported in vManage GUI, but it works fine using the API.I am creating feature template by making a call to POST /dataservice/template/feature/ with f...
We poll the following REST endpoint for tunnel statistics for hundreds of thousands of tunnels.The poll is performed for the last 30m on the hour and 1/2 hour marks. https://VMANAGE_HOST:8443/dataservice/data/device/statistics/approutestatsstatistics...
Hi, I am running vEdge 19.2.2 on EVE-NG PRO and having an issue with any vEdge dropping connections after a period of time. After rebooting a vEdge and doing a show control connections, it shows connections to vsmart, vbond and vmanage with status "...
Hi Cisco Community, I am running SD-WAN lab (version 20.3.2) in EVE-NG and I was in the point where all WAN edges are properly registered to the vManage. However, I noticed that during some time, the DTLS connection or just the transport connection i...
Resolved! SD-WAN Lab in EVE-NG
Hi, I am trying to build a SD-WAN lab using EVE-NG, so far the images for vManage and vSmart are booting ok but i cannot get to boot the image for the vEdge Cloud i have tried with 3 code version always with the same results, they are stuck in Initia...
