We have a hosted application with 2 data center locations, and a SDWAN connection to be installed at each remote site. Site 1 is the preferred route, with Site 2 being the backup. As the connections come on separate routers setting the routing ...
Forum Posts
Resolved! vManage services just stop
We have just 2 vManages... very few devices overall.. one vManage and East coast replicates database to the other one on West Coast. The code is 20.5The problem... both of the vManages just stop all their services at a certain random time say eve...
Hi I'm trying to re-use vEdges for new branch site.The vEdges were used to use for another site which was closed and they are still registered with the old template as unreachable state on vmange.How can I detach the old template from offline vEdge...
Presently we have a full mesh network. I don't want to go to a hub and spoke model, but I would like to implement dynamic on demand tunnels. I am trying to set one data center as the primary hub, and another data center as the secondary hub. Issue I ...
Hello everyone,I'm trying to create gre-tunnel over cisco isr4351 with template in vmanage. but after searching and watching related videos it's possible to create gre's only over vedge and vedge-cloud routers. But there isn't any similar template fo...
Hi, There is office movement where vEdge was running and I expect the IP address on the new Internet line on the new office will be different from the old IP address.So vEdge device can't be online with controller as it still has the old Internet IP ...
Hello everybody,I have created my own sdwan lab with viptela vedges. I am trying to multicast routing on Service VPN ( vpn1) as described here https://www.cisco.com/c/en/us/support/docs/routers/sd-wan/215104-configure-and-verify-vedge-multicast-ove.h...
Hi guysI am using version 20.1.6, with cEdge ISR4331. I deploy AAR follow this guide:https://www.cisco.com/c/en/us/td/docs/solutions/CVD/SDWAN/cisco-sdwan-application-aware-routing-deploy-guide.html#ProcessMonitortheWANtransportpathcharacteristics My...
Hi guysI have bellow topology. I concern that load-balancing and 2 internet connections can cause any issue with IPsec tunnel ?. Because sometime I see cEdge down in vManage, although 2 internet line is ok.
Hi together, I have a problem with the vManage VM. I have an ESXI with the vManage. I did the following steps installing vManage: https://sdwan-docs.cisco.com/Product_Documentation/Getting_Started/Viptela_Overlay_Network_Bringup/03Deploy_the_vM...
Hi guys, I would like an opinion on a case, please. I need to close a VPN tunnel (site-to-site) between the ASA of SITE-A with the ASA of SITE-B, but in SITE-B we have a scenario with Cisco SD-WAN. On SITE-B the ASA is behind the Cisco SD-WAN. I noti...
Hi friends,can you please help me to understand the Tunnel concept use in the SDWAN.1.What is the tunnel source address ? (is it physical IP address bound with the tunnel)2.What is the tunnel IP address ? (is it the system IP)3.WAN-Edge device use s...
First, according to several of Cisco documents (v19.x and v20.x), some state "You can only activate ONE centrailized policy" while others state "you can have one control-policy and one data-policy activated (e.g. one inbound; one outbound"... So whic...
I have a situation were the status of ipsec sdwan tunnel shows up on the router CLI but when monitoring the tunnel from vmanage 20.3.3.1 GUI (SDWAN router ios-xe 17.3.4a) it shows down .... even though statistics and application monitoring are all be...
Hi guysI am using version 20.1.6 and sometimes a I got account locked error although I don't input wrong password. This time it happen with vManage & vSmart. I have noway to fix it, just waiting they are unlocked.
