We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
I've been using the SD2005 for a while now. Nothing physically has changed as far as cabling. No new hardware has been added. I'm unaware of any software auto update, but it's possible that the connection that's causing the problem has auto updat...
Hello All I have SG300 Switch and i use it as L3 (Core switch) ,There are 12 switch is connected to it. I have 3 Vlans My problem is i got a message (%ARPARPTBL: ARP Table Overflow, aggregated (9) My TCAM IPV4 Routing in use 128 IPV4 Rou...
Is it possible to add Transceivers (SFP) MGBLX1 (1000Mbps Singlemode) into a SG350XG-24F-K9-AR, even if all poprts of the switch are 10G Ports? Thanks & regards
I need to upgrade Firmware on two Cisco switches SG300-10 to the latest version 1.4.8.06. Those switches have currently installed version 1.0.0.27. So, there are 15 Firmware releases in between those two. Can someone please suggest what would be the ...
Hi everyone, I have a SG500-52 switch that I inadvertently shut off power to the other day. When I restored power, the switch did not boot correctly so I connected to the console port. On boot, the switch displayed the following message: The MAC ...
We have several APs connected to this Sw and after a reboot only start some AP Firmware Version: 1.4.5.02 PID VID:SF200-24FP V05
Hi, I got a problem with 2x SG220 50p POE, actually I can't get the CPU load from snmpwalk with the OID: ".1.3.6.1.4.1.9.6.1.101.1.9.0 ". Any advice? The FW is the latest available. THXIA
Trying to configure newly purchased sg350 switches. The one I am now working on has the most current firmware version 2.3.5.63 and the timeout set to never but every time I go to a different section of the UI, I must log in again. How to fix this??
One of my clients has a SF300-24P switch that was running 1.2.7.76 firmware we were having some issue with network connectivity so as one of the troubleshooting steps I upgraded just one jump to 1.2.9.44 firmware, I would like to upgrade it some mo...
Resolved! Difference SG300-10MP and SG300-10P
Hi,can anybody tell me the difference between these two models? In the data-sheet I don't find any differences, but probably there are some ...Thanks in advance, Karsten -- Don't stop after you've improved your network! Improve the world by...
Hello, I wanted to understand the Cisco SG 220-26, and I have a quick start manual for it that says: "100M LED (if present)—(Green) Located on the right of the port. Lights steady when other device is connected to the port, is powered on, and a ...
Resolved! SG500X-48 DHCP issue
I created 4 VLAN on SG500X-48 switch, with default VLAN 1 disabled.(AD, DHCP & DNS server IP = 192.168.11.88, Default Gateway IP = 192.168.11.1)DHCP server has scoops for VLAN 11, VLAN 21, VLAN 31 & VLAN 41VLAN 11 - new default VLAN for AD, DHCP & DN...
Units: SG200-18 and SG200-8 VLAN400 Receiver is on SG200-8 and Source is on SG200-18SG200-18 Port18 is set up as a trunk port with VLAN400SG200-8 Port1 is set up as a trunk port with VLAN400IPTV reciever is on SG200-8 Port2 also VLAN400.IPTV sou...
Recently pulled an old SG300 out of storage to use for a temporary environment. After reseting the switch, the system light only rapidly blinks. No ports will even show link, and the serial console provides no output, and unsurprisingly the switch ...
Greetings, I have a problem with several sg500 24p switches, in which I have configured two vlan, one for voice and another for data. Configured like this, voice tagget and untagget data. When the two vlan are connected to the same port, and a physic...
