Update: This portion of the project has finished earlier than initial projections. We are approaching our latest step in relabelling posts across the Small Business board. 1 week from today, read-only mode will be active on this discussion board fro...
Forum Posts
Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Installation Guide - Catalyst 1300Hardware Installation Guide - Catalyst 12...
any info or available documentation on this release?
Hello,w'd like to renew our SG220 Campus Switch to CBS250. Any procedure to migrate the configuration file (.cfg) from SG220 to CBS250. as they are 95% same, we do not want to rebuild all from 0 on CBS250.Configuration Migration Tool propose by Cis...
HI!I am looking for a little help here. I have two Cisco CBS350-8MGP-2X switches interconnected. They are not stackable. Based on the cisco specs for the switch the packet buffer is 1.5mb and the forwarding rate is 46.13mpps and 62gb switching capaci...
Resolved! how to check DRAM parameter on cbs250
Hello everyone, my customer recently purchased a CBS250 device, and requested to display DRAM information. I tried show version but it doesn't show any information about DRAM, Are there any commands support this?
Hello everyone!I have the next switch CBS350-48P-4X with this version: 3.0.0.69.I have a problem with CDP on the ports where I have IP phones. It gives me the next warning:%CDP-W-DUPLEX_MISMATCH: Duplex mismatch detected on interface gi1/0/10.The IP ...
When using the snmpwalk command to query a Cisco SF302-08PP switch with the -c public community string, am not able to find data related to Optical Module Status and CPU Utilization. I am trying to collect the data of a switch through snmp protocol u...
Hello everyone, trying to connect to switch via console.The switch has a DB9 socket as a console, I connect the serial cable to the PC via a USB adapter. In the PUTTY application, I select the appropriate COM3 port and the console is displayed, but I...
I need Switching power adapter for both SG300-10SFP or SG350-10P Cisco switch. Before It was FSP-090 DMBC1 but this power cord cable is not available now. Instead the vendor offered me FSP-090 AWAN3 . I need to know that is FSP-090 AWAN3 is compatibl...
Hello, We have several CSB110-24T switches in our office that are working normally except the LED of the ports. When we connected the switch port to one end of a CAT5e cable (the other end doesn't connect to any device or patch panel), the LINK/ACT ...
Hello ,How we can get all the information presented in this image through SNMP Protocol (the target switch is cisco sf302-08pp)Thanks in advance.
Resolved! CBS350 Multiple destination SPAN/RSPAN
Hi,Does the CBS350 support using the same data source(s) for multiple destination session definitions?I currently have a RSPAN destination configured using a VLAN source, and would like to use the same VLAN source for an additional SPAN destination s...
Hello,During planned electricity poweroff - we had a strange issue with 2x SG200-50P switches. After electricity come back - our switches booted properly, but some devices were not powered through PoE (mostly IPTV camera). So we've tried different po...
Hello, I'm, running a SG350XG-24F with software Version 2.4.0.94 and got lots of the following log messages: 26-Oct-2018 04:44:00 :%Box-W-I2C-FAILURE-READ: I2C failed to read information from device at address 0x70 on bus 1 offset 0x09, component C...
Resolved! Stacking on CBS350-48T-4X
Hi everyone, I have two CBS350-48T-4X and I would like to stack them, my question is it possible using the Lan RJ-45 ports to configure the stack? When I'm doing the Stack configuration, it only allows me to select the 4x SFP ports. Is there an addit...
Hello everyone,i have a sg300-28 Switch and want to restore the config on an other sg300-28PP Switch? Is that possible? And are there fw ver requirements? thx in advance
