Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

  Hi,   I am getting below log message on a WS-C2960S-F48FPS-L. Could this be a bug?     Apr 26 00:54:44.850 CET: %PLATFORM_ENV-1-PWR_RPS: Redundant power supply faulty or in standby mode Apr 26 00:55:03.121 CET: %PLATFORM_ENV-6-RPS_PRESENCE: Redunda...

nyi gbe by Level 1
  • 861 Views
  • 1 replies
  • 0 Helpful votes

We are taking the network offline this weekend to do software upgrades on almost all of our equipment.  But my manager does not want to take off-line our 6506-E VSS core because he thinks we don't need to.  We are currently running version 15.1(2)SY7...

mrkaufman by Level 1
  • 550 Views
  • 5 replies
  • 0 Helpful votes

Hello, I'm doing the configuration of CISCO stack (3 switch 2960X with FlexStack module) and I'm wondering if it's a good practice not configure stp since this stack is directly connected to a router (internet router) and the others connections are ...

Hello Everyone,i have two routers and two isp.i will need help on possible best way of integrating the two links either using a single router or using the two routers.The routers version are 1800 and 2900 respectively.Please find details below.I will...

Hi, i have this scenario: I have two ISP. One of them come from a frame relay conection on serial port on a router called RT1. The other one is a proxy, as a host on my network. This network are directly conected to RT1 via eth0/0 Furthermore, i have...

vruiz by Level 1
  • 1159 Views
  • 4 replies
  • 0 Helpful votes

Hello all, We are a campus environment. We just introduced small port switches(8 ports & 16 ports---c2960 model). Since when we inducted these switches, we are getting MACFLAP errors on trunk link. We have same config. on uplink. This error is only o...

Hi, I have a SG200-26 26-Port Gigabit Smart Switch and port 2 has just stopped working. I have tested several active lines that are working in other ports. I have also rebooted using factory defaults and still no joy. Any ideas?  Your help would be ...

Hi, I have Infra setup like Avaya device for VoIP connected to switch 3850. Planning to install a fax machine  Questions 1. Whether RJ45 will support RJ11, Since Fax Machine Jack out is RJ11 2. Avaya Device Placed in 9th Floor, I need to install Fax ...

aswanths1 by Level 1
  • 659 Views
  • 8 replies
  • 0 Helpful votes

we have two AsA firewall failover, primary:  192.168.0.1 secondary: 192.168.0.2, all the server now has the default gateway 192.168.0.1, what if primary is down, do we need to manually change ip to 192.168.0.2? in ASA firewall how to acieve active/ac...

Mary by Level 1
  • 226 Views
  • 1 replies
  • 0 Helpful votes

does snmp applicable to both router and switch and netflow can only be set in the router? if i have snmp trap enabled, do i still need netflow? which additional functionality can netflow bring

Mary by Level 1
  • 789 Views
  • 1 replies
  • 0 Helpful votes

Hello Every one. I have a question regarding an ASR 1004. Recently the device crashed because some ipsec activity. I tried to find a bug that could be affecting the IOS-XE but I didn´t find anything. So I decided to upgrade the operating system to th...

Review Cisco Networking for a $25 gift card