Buy or Renew
Buy or Renew

Switching

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Resolved! Add Cisco 3750-x into stack

Cisco engineers, I'm looking to add a 3750-x into a productions stack with the following members - Switch Ports Model              SW Version            SW Image                 ------ ----- -----              ----------            ----------        ...

Resolved! EIGRP choosing route from supernet and External Route

 Hi everyone, Here is setup -----172.24.104.x----Server-----FW------SW1--------EIGRP nei   SW2-------EIGRP nei-------SW3------user  PCUser connected to SW3 needs to access server   172.24.104.x SW1 knows route to destination 172.24.104.x via FWSW1#sh...

mahesh18 by • Frequent Contributor
  • 1502 Views
  • 18 replies
  • 0 Helpful votes

Etherchannel Load Balancing

Looking at the attached diagram, would it make sense to have the Load-Balancing Algorithm on the Core to "Destination MAC" and then on the Access Layer Switch Side to "Source Mac" address? Keeping in Mind there would be multiple Servers and also 100s...

GRANT3779 by • Frequent Contributor
  • 214 Views
  • 4 replies
  • 0 Helpful votes

Low memory I/O on 2960s

Hello all,we recently installed cisco PI 1.3 and on the "Top N Memory Utilization" dashboard I am seeing that many of our 2960s switches have high memory I/O.Most of them are runningc2960s-universalk9-mz.122-55.SE3c2960s-universalk9-mz.122-58.SE2.bin...

4510 Port Security Issue

Any thoughts on the following topic??  In our organization we've started to migrate from stacked switches to a Catalyst 4510R+E with 2 SUP 8E's for our LAN.  When we started migrating our old lines to the new switch's ports, our IP phones / printers ...

Network ports stop responding with inactivity

We installed a 4510 a couple months ago and this past weekend there was a reported power surge on the floor.  Since then I have specialized printers and thin clients that will stop responding to pings after periods of inactivity. If I disconnect the ...

mlinval by • Beginner
  • 202 Views
  • 2 replies
  • 0 Helpful votes

Cisco WS-C3750X-24S-S specifications

Hi ,We are going to use Cisco WS-C3750X-24S-S as L3 switch in the network which will have all fiber uplink  ,this is Switch is GE SFP switch and i will have 12 fiber uplink .and 4 Ethernet connectionsplease help in ordering the hardware. Also if i am...

uma.kashi by • Beginner
  • 364 Views
  • 3 replies
  • 0 Helpful votes

Resolved! VRF on 3750

HiI have a single 3750 in a lab with one VRFvrfdrawing1.pngI am trying to route traffic from the global space to a host in the VRF but I cannot get it to work. The relevent config is as follows, I cannot figure why this will not work. Any suggestions...

Resolved! CISCO 1841 Won't Overload NAT

Hi all,Hope I'm not too out of line here. I have Cisco 1841 with software version 12.4. For some reason, nating on dialer interface won't overload. I can only access google and facebook, but not any other site, it will just keep on trying to access t...

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers
Spotlight Award Nomination