Buy or Renew
Buy or Renew

Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Start a conversation

Resolved! VSS etherchannel problem

Hello,We have two 6500 & are trying to create VSS for this.Below are the configurations on both switches;Switch1:-switch virtual domain 100 switch mode virtual switch 1 priority 110interface Port-channel1 description VSL to Switch2 no switchport no i...

suthomas1 by • Level 6
  • 995 Views
  • 4 replies
  • 0 Helpful votes

Resolved! Nexus 5548 - ipv6 interface

Is it possible at nexus 5548 with daughter card to assign ipv6 address to interface?I have gone thru lot's od docs cisco says on tech doc:• IPv6 Routing Protocols: Static, Open Shortest Path First Version 3 (OPFv3), Border Gateway Protocol (BGPv6), E...

massive issue with hpux on hp blades

Hi allWe have an ongoing issue of really slow file transfers to our hpux servers running on blade chassis using virtual connect.The transfer download starts off around 3Mbs then goes to 512k, however the upload is much quicker. We are transferring a ...

CISCO2921/K9 or CISCO2921-SEC/K9

I actually asked for the pricing of 2921 router to a local reseller and he gave me 2 optionsCISCO2921/K9 CISCO2921-SEC/K9The first one is cheaper than the second. I have 2 questions:What's their difference ?Can the cheaper one be later converted into...

Nexus 5500 L3 and IPv6

Hello TogetherFor the new Nexus 5548 and 5596 is a L3 Daughter Card or L3 Module available. Unfortunately it doesn't support IPv6 in Release Release 5.0(3)N1(1). Is it planned for the future to add support for IPv6 and if yes in which release is it p...

auto upgrade path ... how to set them

on show boot-command i found an entry called "auto upgrade path". what stand it for?Switch#sh bootBOOT path-list      : flash:/ies-lanbase-mz.122-55.SE5/ies-lanbase-mz.122-55.SE5.binConfig file         : flash:/config.textPrivate Config file : flash:...

Resolved! How switches detect different mstp regions

Hi community,It is said that a switch detects if  its neighbor switches belong to the same mstp region by comparing its parameter with the neighbor ones. "An MSTP switch can also detect that a port is at the boundary of a region when it receives a le...

minh_hieu by • Level 1
  • 1721 Views
  • 3 replies
  • 0 Helpful votes

Resolved! PPPOE Adsl urgent issue

dear all,am using cisco router 2811 with HWIC ADSL card needed to be connected to the internet.i tried using one of the following ATM configuration but connection to the internet failed as the virtual-access interface remains in down state.Please see...

IS GLBP SUPPORTED ON NEXUS 5500

I am wondering if GLBP is supported on nexus 5500I have 4 5548s I want to run glbp on but the feature is not listed to activate.version 5.2(1)N1(1a)I have features hsrp and vrrp but no glbp.  According to what I read from Cisco you don't need special...

mcg-tulsa by • Level 1
  • 4377 Views
  • 8 replies
  • 0 Helpful votes

DHCP Snooping on a trunk interface

HelloI have the following set up on my network.My problem is that i cannot get a DHCP address on the client.I have the following config for both:Global#################################ip dhcp snoopingip dhcp snooping vlan 10 , 20 , 30################...

Portchannel Issues

Hi,we have cisco 6509 switch with ws-x6748-GE blade We have configured layer2 portchannel with a HP blade switchchannel-group mode is set to 'Active'Portchannel establishes but I could see several portchannels are created Pasting the sh etherch summa...

View All
Review Cisco Networking for a $25 gift card