We think we have configured the ACE and Tacacs properly as we auth, but are not able to enter into configuration mode.Any advice will be helpfulACE-4710 A4(2.3)Thanks
We think we have configured the ACE and Tacacs properly as we auth, but are not able to enter into configuration mode.Any advice will be helpfulACE-4710 A4(2.3)Thanks
Hello,I'm wondering if this is possible.I have two Nexus 5596UP that will be connected together via VPC-Peerlink. From there I want to connect both 5596UP's to a 6509-VSS via VPC.Can anyone tell me if this is possible and the best way to go about th...
When I try to add an IP address to a port-channel interface on a 3845 ISR I am getting an error that seems to imply that only L2 etherchanneling is possible. Am I missing something?Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version...
Can you have a look at the below config and let me know what I am missing. We want to send the traffic from three IPs (defined in ACL 171) to 10.1.60.16 and send the rest of the traffic in that VLAN to 10.1.0.1When we did a traceroute from 10.1.101.3...
Below is the relevant part of my router config. What I'm trying to achieve is all traffic ultimately going to 68.164.204.26 be sent to 10.72.2.10 from all devices on the inside of my network. So, if host 10.61.23.101 wants to send to 68.164.204.26, i...
Does the 3750G-12S-E support Advanced IP Services version of IOS?
I'm seeing some odd behavior on one of my 3750 switches and was wondering what commands I can use to troubleshoot with? Or use for diagnostic review? The two issues I'm seeing are I use Packettrap switchport mappper and for some reason on this switch...
Hi everyone,I got a problem switchport error disabled by itself,using network assistant I can see the error with this description:_____________________________________________________________________________________________________________ This...
What is the maximum group of HSRP Group that supports the WS-C3750G-24T-S running the IOS c3750-advipservicesk9-mz.122-44.SE2.bin?I have this message:Mensaje ERROR: %Platform already has maximum FHRP groups configured
Hello,I am trying to validate a Microsoft NLB cluster setup that is running in IGMP Multicast mode.I can see the IGMP snooping result:300 239.255.82.160 igmp v1 Gi1/0/9, Gi1/0/10, ...
Main Router:interface Loopback0 ip address 1.1.1.1 255.255.255.0 ip nat outsideinterface FastEthernet0/0 ip address 10.15.16.5 255.255.255.0 ip nat inside ip policy route-map NAT-EEinterface FastEthernet0/1 ip address 192.168.0.250 255.255.255.0 ip n...
Dear All,when reading cisco documentation about the OSPF virtual links, I had come accross the following statement -All areas in an OSPF autonomous system must be physically connected to the backbone area (area 0). why they should be physically...
Hello guys, hoping you can help me out. I have recently implimented an RV016 device into our network. We have a bonded T1 service with Paetec/Windstream (5 static IPs) and also a cable connection with Comcast (no static IP). The T1 has been our pr...
Dear All,I have configured OSPF in packet tracer.Please find the diagram and below configuration -for R1 -interface Loopback0ip address 1.1.1.1 255.0.0.0!interface FastEthernet0/0no ip addressduplex autospeed autoshutdown!interface FastEthernet0/1ip ...
Dear All,If the users are more consider it requires /18 subnet to cover all users in a same vlan. So it will be a very big vlan. Is this normal or vlan should be small?KVS
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-19-2025 08:02 PM | ||
06-19-2025 07:25 PM | ||
06-19-2025 07:22 PM | ||
06-16-2025 07:47 PM | ||
05-27-2025 03:30 AM |
User | Count |
---|---|
12 | |
10 | |
7 | |
6 | |
5 |