Hi i have the below msg appear on my 6500 , what is the reasons and how to sove it %IP-6-PHYBCASTDROP: Physical broadcast packet detected and dropped, thanks
Hi i have the below msg appear on my 6500 , what is the reasons and how to sove it %IP-6-PHYBCASTDROP: Physical broadcast packet detected and dropped, thanks
HiCould anyone advise the purpose / meaning of the following statement?"no event manager policy Mandatory.go_switchbus.tcl type system"Thanks.
Hi,We are currently experiencing an issue when we place a sub-if into a VRF.What we are seeing is when the sub-interface in configured out of the VRF the service works correctly, however when we place the SUB-IF into the vrf the upstream switch doesn...
Hello,I need your help about the subject.My customer need to access to the Internet via IP-VPN network,and also they need torestrict only using http and https access from a specific networking segment.But they have a own proxy server,and they have to...
Hi all,I am sitting my ROUTE exam in two days and wanted to confirm whether I am expected to know whether the 'auto-summary' command (and autosummarization behaviour is enabled OR disabled by default in EIGRP?I have never used EIGRP outside of my lab...
in my LAN the all access layer switchs/stacks are connected directly to core backbone switch (cisco 6509) via sfp fiber-optici want to protect my spanning tree setup with the "root guard" command.1. where would i set this ? on uplink ports on access ...
I have an ASA 5505 with Security Plus LicenseAny help would be appreciated on the scenario below. I'm more familiar with asdm gui than command line.I have 5 Static IP Addresses from my ISPI have the following interfaces. Outside (vlan 2) / Inside (vl...
Hi Everyone.I have set up IPSEC tunnel in labOn both devices i see this message in logsDec 1 09:52:49.600 MST: %CRYPTO-4-RECVD_PKT_NOT_IPSEC: Rec'd packet not an IPSEC packet.(ip) vrf/dest_addr= /192.168.13.1, src_addr= 192.168.23.3, prot= 47Second...
Hi everybodyPlease consider the following example: rest of network------f0/0-R2- f0/1---------------------R3R2#show ip routeC 200.200.200.0/24 is directly connected, FastEthernet0/1C 199.199.199.0/24 is directly connected, FastEthernet...
Hi,while i am configuring a port on switch .The switch reloads.After reload the show version saysSystem returned to ROM by bus error at PC 0x458F6C, address 0x0show version from the effected switch isCisco IOS Software, C3750E Software (C3750E-UNIVER...
`I am having a problem with redundat default links in the below topology.The router sare configured as below.3845 RoutersRouter 1 (Left)router ospf 666log-adjacency-changes network 192.168.0.0 0.0.0.3 area 0 network 192.168.3.0 0.0.0.3 area 0network ...
Helo, does the WS-C2960-24TT-L switch support power over ethernet ?Thank you.
Hi Everyone,Need to Config 2 ports of Core Switch that goes to Distribution Switch which is stack switch in Etherchannel Remotely.Need to confirm if i can do this remotely without outage?ThanksMahesh
Hello Expertscan someone help me to understand how ISP restrict bandwidth for its customers. cdp neigh command on our Internet Edge router indicates the link is terminated on cisco 3750 switch what configuration is done on the switch to restrict the ...
I've just replaced a Cat6500 w/Sup 720 in a data center switch with a Sup2T ... and a few minutes after booting, it spat out:%QM-4-TCAM_ENTRY: Hardware TCAM entry programming failed for slot 7 intf Gi4/39 dir IN: <CONFIG_UPDATE_REQ> TCAM Req Error: F...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-30-2025 10:17 AM | ||
05-27-2025 03:30 AM | ||
05-27-2025 12:59 AM | ||
05-23-2025 10:30 AM | ||
05-15-2025 09:37 PM |
User | Count |
---|---|
9 | |
8 | |
5 | |
4 | |
3 |