hi , from ccnp route cisco press book , the last of ipv6 tunneling i have a table Table 18-4 Comparing IPv6 Multipoint Tunnels Topic Automatic 6to4 ...
hi , from ccnp route cisco press book , the last of ipv6 tunneling i have a table Table 18-4 Comparing IPv6 Multipoint Tunnels Topic Automatic 6to4 ...
Hi I'm trying to configure "IP PIM SPARSE-MODE" command on a vlan interface on a 3560E switch but it doesn't give me the option to do this. The only option available is ip pim passive. What would cause this ? On the same switch a physical interface i...
I have a Catalyst 3560'm trying to use ASDM, i do not know how to set it
HiI just got my Cisco SG300 28, but I have some problems getting the routing to work. I get the vlans to get to the router, with the default route. But not getting them to talk with each other. I can ping the IPs from the cisco, but I am not getting ...
I have a customer with a 3750x4 stack. We rebooted the stack over the weekend and the master did not come back up. Upon investigation it was discovered that tghe master was set for Manual Boot. I tried issuing the "no boot manual" command in Global C...
HiI am seeing a strange situation on my 6500 switch which I am not able to understand and hence asking :). By having snmp walk on '1.3.6.1.4.1.9.9.109.1.1.1.1.3' (== cpmCPUTotal5sec), I came to know that there are two processor and the cpu util for s...
HiMy 2960-24TC-L switch is startet up and shows up: switch:Have tried to upload new image with xmodem without succes.There must be a procedure to upload the new image, I have looking for hours and can not find the procedureCan someone help please.Eri...
Hi AllWe have a pair of 6509-E with SUP 720 which constantly shows decently high CPU - 60-80 %... We arent sure what is driving this CPU ! Show proc cpu doesnt give any process which is consuming the cpu ! Initially we thought it could be due to RPF...
Could someone with Cisco IOS 12.4 Basic check to see if the command "ip nat pool" is available?We have 12.2 basic and I know it is in the 12.4 Advanced and 15.1 Basic versions (too large of a jump in version for management). Our budget is very limit...
I have a catalyst 3560G switch that is having a hard time giving power to a Meru AP 320. The following error is on the switch:010422: *Sep 25 16:53:48: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi0/1: Power Controller reports ...
hi ,i have the topology below :"Vmware pc"<===="PC"<==========>switched 2960<=======>-Gi0/1-Routernote that:PC is the physical computer and inside it nother operating sysetm called "vmware pc" on router , we have an ip from vlan 1 on the physical i...
Hello, I have a hub and spoke WAN that conisits of one core location with with a 6500 and nine other buildings using 4006 Catalyst that conenct back to the core via dual gig fiber. We are using EIGRP at each location as well as the core. I was tesi...
Hello,We're using a context using vlan 24. But we want to create another instance in the same vlan (24) using a different VIP. Could someone tell me if this is possible and what the config would look like please.Thank you
GRE Failover
Hello, I have a Cisco 2921 router. I have a few IPSec site to site VPN's configured and a terminal server behind the 2921. The problem I am experiencing is I also publish that terminal server to the internet. When I have a NAT setup to allow a...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-23-2025 10:30 AM | ||
05-22-2025 08:23 PM | ||
05-20-2025 09:58 PM | ||
05-15-2025 09:37 PM | ||
05-06-2025 02:02 AM |
User | Count |
---|---|
6 | |
6 | |
4 | |
3 | |
3 |