Resolved! radius and autentication methods
Hi everybodyDoes Radius protocol only support 802.1x authentication?thanks and have a great day.
Hi everybodyDoes Radius protocol only support 802.1x authentication?thanks and have a great day.
Hi,I have a doubt in ospf metric calculation. I will atatch a topology with this thread.In that topology i expected the routers R1 and R4 to reach R5's networks via two routes. one through R2 and other through R3. i.e I expected they should choose tw...
Hi,I have 3 Catalyst 3750 in same stack, the IOS version is 12.2(53)SE2. Today we can not telnet/ssh to this switch, but ping is ok, and switch function is ok. I try to access the console port, it show "low on memory, try again later". After I reboot...
Hi,Hi,I configured a dynamic vpn(easy vpn) in a cisco isr. But the vpn clients cannot access any of the lan devices. VPN pool is 10.0.0.1- 10.0.0.20 & internal network address is 172.17.x.x.Please help me out.see my configuration:R...
Trying to build up a test lab. I have three routers connected via serial cable.Router 1--------------------- 10.20.20.10 I 10.20.20.11 s1/0 Router 3 I 10.20.21.11 s1/1Router...
Hi,we have cisco 2960 switch which is connected to a cisco 2811 router. Anyone can help to fix the flapping issue between these two devices??The following actions i have taken, but no result..I have changed cables.have set speed to 100 and duplex ful...
Hello Experts.This question is related to know the traffic flow in redundancy network where i have two cisco core switches and a VLAN 70 is configured with virtual IP address 192.168.1.1/24 as we are using HSRP protocol.Physical IP address of Core Sw...
Hello all,I recently ran into an issue related with a route-map, and I am not sure what caused it. I am hoping that someone on the forums can provide a logical explanation.I connected to the router via telnet through GRE tunnel 10 on the router.The ...
Hi All,I'm using GNS3 0.8.2 on Win7. I have created a local network cloud and given a 7200 an IP of 10.1.1.10/24. ADSL router on this network is at 10.1.1.1. The Win7 machine is at 10.1.1.2. A Linux VM on VMware Server 2.0, on a bridged e1000 is at 1...
Hi all,i have a problem with multicast flooding in our network.We have two stacks of 3750x switches, on each stack connected Video servers (that get real video streams from IP cameras), each server has a number of IP cameras .This traffic is unicast....
Hi One of the 6500 was going in bootrom mode, so I have formated the flash disk using the other Cisco 6500 switch and copied IOS file to the boot disk. But the 6500 booting failed with the following errorrommon 1 > boot disk0:/s72033-adventerprisek...
Hi Guys,I have two devices connected to each other using a crossover cable. The first device output is as belowcisco WS-C3750G-12S (PowerPC405) processor (revision H0) with 118776K/12288K bytes of memory.Processor board ID CAT0837Y165Last reset from ...
In a lab environment, I have a stack of two 3750v2-48ts switches. I upgraded the stack from 15.0(1)SE2 to 15.0(1)SE3 using archive download-sw. Switch 1 in the stack reloaded and came back with the new image.Switch 2 appears to be dead. No console ...
Hello,I have a problem to figure out how to configure a backup route to the internet. My client has 2 ISP and basically they want to use 1 ISP and in case the ISP fails, use the other one as backup route to the internet.The topology looks like the o...
I am planning to upgrade cisco 4948 IOS upgrade.We have few with older code( 12.2(25)EWA7), when issue sh ver shows as Catalyst 4000 L3 Switch Softwware. while newer version of the switch show as Catalyst 4500 L3 switch.1 Is this/(sh ver output) just...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
05-06-2025 02:02 AM | ||
05-06-2025 01:05 AM | ||
04-23-2025 06:26 AM | ||
04-23-2025 06:18 AM | ||
04-19-2025 09:40 AM |
User | Count |
---|---|
8 | |
7 | |
5 | |
4 | |
3 |