Hi,Does any one have a recommendation on a good place for Nexus Training in New Jersey,New York area.Should we take a training course on 5000/7000 combined ?ThanksStan
Hi,Does any one have a recommendation on a good place for Nexus Training in New Jersey,New York area.Should we take a training course on 5000/7000 combined ?ThanksStan
Hello,I am preparing for the CCIE R&S lab and have couple of doubts around VLSM. Subnetting itself is an easy task when you take a major network and divide it into several subnets. But this is currently not my problem. My problem is with VLSM or vari...
I am having some issues finding the specific information about EnergyWise that I am after.Does energywise shut down the port? So If I have a energywise schedule on a port that does not have a PoE device will that port be effected?I have a few PoE dev...
Does VSS have more redudancy than HSRP because VSS has both distribution switches active instead of passive and active like HSRP?
Hi,I am wondering how to secure with ACL access to special VLAN in my network that is only for VOIP telephony.My company has VTP domain set on router, and also on router VLANs are configured over subinterfaces.So point is to have devices in that spe...
Dear friends,Just by experimenting I have stumbled across the possibility of configuring and successfully applying VLAN ACLs (VACLs) on 2960 series Catalysts in IOS 12.2(58)SE1 LANBASE. However, there is absolutely no mention about this feature in an...
Hi folks!I have few questions about SUP7E perfomance. There are they:Catalyst 4500 SUP7e switching capacity is 848 GbpsCatalyst 6500 Sup720 backplane is 720 GbpsSo this is mean that SUP7E has capability to switch more traffic than SUP720 ?Second ques...
We tried to install a 4 port gigE card into the back slot and it didn't show up.Apparently it's saying that it can only support one gigE switch...is it counting the two onboard ports as that switch?Can I disable them to get it to recognize the card o...
Hi Guys,I have an issue whereby I cant seem to get multicast to stream outside a vrf.I have the following scenerio;6500 switch, sup-720 loopback set as the rp.I have created a vrf (lite), which is sat behind a fwsm. I have enabled multicast routing i...
Has anyone configured one of these? I can't find any information about how to configure the VDSL controller, anywhere.I have one, hooked up to a VDSL line, ready to configure. Now I can't find any information on Cisco's website about configuring th...
I have been searching but couldn´t find the forwarding rate of the 3560 v2 switches (expressed in mpps).Does anybody has that information?Or is there a way to deduce it from other specifications?thanks for your help.Sergio L.
I have a Catalyst 2960-48-TTL that I have a problem with when writing boot system flash:filename information. I get a response of vb:: Read-only file system.I removed all other IOS images from the flash: directory except the one that I want to boot....
How can i setup a switch ethernet port to always send back what it received on the same port? Computer---->switch switch always sends back the ata the computer sends it.Is there a route option for that?Thanks,Mark
Dear AllMy 6513 max cpu utilization reaches around 60 % however, avg CPU remains around 10%. What is the ideal maximum cpu and memory utilization percentage? Can someone explain. 6111114444411111444441111122222444443333344444 3333311100 90 80...
I am having issues with IP SLA and tracking to inject a different default route. I am running 15.0(1)M4 so the commands are a little different than what I have used on 12.4 but I followed the 15.0 guide with no luck.Here is what I have.track 123 ip ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-23-2025 01:45 PM | ||
07-08-2025 11:44 PM | ||
07-04-2025 02:13 AM | ||
06-26-2025 10:05 AM | ||
06-16-2025 07:47 PM |
User | Count |
---|---|
13 | |
11 | |
9 | |
5 | |
4 |