Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Hi,I cannot find the differences betwen functionalities of Cisco ASA firewall and IOS firewall featureset available for routers (starting from 12.4.x) .Performance and price of both options are available.Can anyone suggest where to find comparison be...

resurector by Level 1
  • 12702 Views
  • 3 replies
  • 0 Helpful votes

Hi All,Presently i have encounter a funny issue. My 3560 vtp mode is transparent and 3550 is in server mode. I have manually configure vlan in 3560 as what is it in the 3550. Logically both switches should be able to ping to each other ( i have inter...

ivanpaseo by Level 1
  • 1467 Views
  • 6 replies
  • 0 Helpful votes

Hi!Our company Intranet consists of 2 regional networks, each of which is a DMVPN network with regional center (regional hub, Cisco 1811) and small branches (spokes, Cisco 871). The hubs of the regional centers are also connected with each other by 2...

Problem FEX hangs on "Image download"current versionkickstart: version 4.1(3)N2(1)system version 4.1(3)N2(1)feature Fex enablefex association 1001.   Is this syntax correct? 2. Then what is the next step after I get image to 5010GettingNexus_5010# co...

I am looking for some help regarding a NAT statement, to prevent some statically NAT'd servers from translating through a VPN tunnel.I have an overload PAT which references a route map which in turn references an access list as follows -ip nat inside...

Hi,I have created this config on switch.p dhcp pool CARLSON   network 10.36.247.64 255.255.255.224   domain-name carlson.com   dns-server 203.122.63.152 203.122.63.154   default-router 10.36.247.81!ip dhcp pool pool2   host 10.36.247.82 255.255.255.2...

I have an ISR with and interface that shows up as follows;GigabitEthernet0/0 is reset, line protocol is downI cannot get rid of the 'reset' state... actually I'm not quite sure what 'g0/0 is reset' really means, I don't recall having ever seen this s...

krjohnson by Level 1
  • 1070 Views
  • 2 replies
  • 0 Helpful votes

Resolved! 887V and BGP

Hello All,I need help i have a  887V and put this IOS:lash:c880data-universalk9-mz.150-1.M1.bin which in the Cisco Feature Navigator which says it that my IOS should have Advanced IP and supports BGP, now the issue i am having is when i want to use ...

I had opened another discussion about this, but for the life of me, can't find it, so please forgive my double post. Last week, our ISP activated a 50Mbps Metro E point to point link between an office that we leased, and our data center.  I do unders...

Resolved! ether bundle

Hi Experts,Of the two modes of bundling- layer 2 & layer 3 etherchannel for uplinks, which one is more advantageous & any reasons one should be used over the other.Thanks in advance.

suthomas1 by Level 6
  • 471 Views
  • 3 replies
  • 0 Helpful votes

HiI have a switch cisco3500, which is connected to another switch2950. 2950is a new one, and 3500 is an old switch. ASA and most of the interal hosts are connectd to the 2950 switch, it shows a 4% CPU utilization. A trunk line from 2950 to 3500 is co...

Review Cisco Networking for a $25 gift card