I have 2 Catalyst 9500, connected in VSS mode. The current physical connections are below:switch 1 Twe1/0/1 <-----------> switch 2 Twe1/0/1 (VSS Bundle)switch 1 Twe1/0/2 <-----------> switch 2 Twe1/0/2 (VSS Bundle)switch 1 Twe1/0/47 <-----------> swi...
Forum Posts
Bonjourmon switch c9200l reste en état V-Mismatch, lorsque je l'enlève de la pile (de 3) et qu'il est seul il est en ready en version 17.06.04 comme ceux de ma pile, je ne sais plus comment fairemerci pour votre aide
Hello I need your help with this problem. We have this DS-C9148S-12PK9 switch that has been left with all the lights on the fixed ports in orange and the STATUS led in fixed red. From the switch, when I access via Putty it shows:Device 0: Model: UB30...
Hello,is it possible to configure the DHCP server of the switch (Cisco SF350-48MP) to offer a dedicated IP address based on the port number but without configuring the MAC address.For example:camera1 connected to port fa1 retrieves always the same @i...
Hello Friends,I am about to upgrade a 3750 , what’s the best version to go for. I am 12.2 (25). Is it ok to jump from (25) to (55) ipservices.second question , after I copied the image file to flash: do I need to create a ‘boot system’ command to loa...
I was applying an access list on a switch SVI on nexus 9300 series switch but when I apply the access list on the out direction of the SVI it blocks traffics to the servers on the VLAN and that's want I want and perfect but the problem is it blocks ...
Hi All,Recently deployed Cisco Catalyst 3850-48P-E Stack Switch. I am receiving a lot of syslog messages ''''Controller port error, Interface Gi3/0/28: Power Controller reports Short detected''''Switch Software version : 03.03.02SE RELEASE SOFTWARE...
Upgrading one pair (within inside the same DataCenter) of the 7000 Nexus. We would like to know if there's any incompatibility issues running different NX-OS versions between both pairs in two different DC`s? https://www.cisco.com/c/en/us/td/docs/swi...
hi,i'll configure a C9300 switch but the C9300-NM-8X isn't installed yet.i can see ten gig 1/1/1-8 interfaces are available.are these reserved for the 8-port module? can i pre-configure these interfaces withoug the said module yet?9300#sh invNAME: "c...
Can you help add the 50GB traffic shaping for etherchanel .I tried but it is not working.
I have the following output when I did "show int gig 1/0/1"Full Duplex, 100 Mbps, 10/100/1000 Tx portsthe switch is 3750X, So my question is that even the ports support up to 1G so here 100 Mbps shows that the attached cable is cat5 right?
We are observing intermediate packet drops in traffic where the cisco C9300-24T is connected to fortigate firewall. We are using copper port on switch side and sfp-RJ45 at fortigate side. Need help to resolve this issue. Thanks.
Resolved! C9500 Upgrade License
Hi.. Currently we have C9500 with network essential license, can we upgrade this license to advantage license? If yes, which SKU should we order? Or we can't upgrade the license and need to buy another c9500 with network advantage installed?
Hello Everyone,We have 3 Cisco switches in our network.1. Cisco CBS350-24T-4G2. Cisco CBS350-24P-4G3. Cisco SG300-28PKindly check attached image file of topology.We have two VLANs- V156 & V157. We have manually created these vlans on all three switch...
Hello,I've been trying to configure the network seen below in Packet Tracer, and so far the big networks are working as expected. My problem is with the connection with the net on the bottom, it is supposed to be a collapsed-style architecture hence ...
