Hi every body!I have few questions.My book says" ASA hardware can act as a firewall,in other security roles,and in a combination of roles."what are those roles as indicated by" other security roles and in combination of roles " in the above excerpt ...
Hi, Folks, I have a number of switches and ports configured as shown below. Request is that I should remove such portfast and stp bpduguard and bpdufilter configurations from production switches.Question:My concern is that such switches are live, cri...
Hi:I have a BGP speaker thats learning a default route from the ISP. I know that I can run OSPF on that same edge router, which makes it an ASBR, by the way, and inject a default route into the OSPF domain by using the default-information-originate c...
Hi every body!I have few quesions:I just got a part-time job at Pizza Hut.During my training, i was told there were 10 pizza huts owned by same owner.I saw cisco ip 2811 phones are being used at my work. Then i also happened to see cisco i...
Hi,I have a quick question: my CPU is running as follows: CPU utilization for five seconds: 79%/73%; one minute: 43%; five minutes: 27%So why is it, when I add up the 5 sec % from all of the processes used, it equals 1.55%? What is using the other 77...
Does Cisco have tool available to customers that would allow us to put in a number of a device (serial, model, smartnet, etc) and return the current status (End of Sale, End of Life, etc.)?My boss is looking for a quarterly report that can be generat...
A 3845 router can it support 6 modules HWIC, 3 modules FXO and 3 modules FXS?
Deleted.
I am trying to understand what causes a currupt IOS image. I have 4506-e that needed to have supervisor replaced becuase the IOS was said to be currupt. I am trying to understand what some of the possiblities that could have caused this.
Hello everyone,I have a number of switches on the network that are linked on the G0/1 port with a CX_GIGASTACK module. I have numerous stacks throughout the network.Some appear to be connecting at the following...Auto-duplex (Full), 1000Mb/s, media ...
Today we had a problem on a trunk port within a HP Blade Center 7000 configured with Cisco 3020 switches. The port that was connected to a blade was sending BPDU packets on one of our main production vlans causing constant topology changes. The serve...
anyone ran into this error in a VDC after upgrade to 4.1(5)?Eth7/16 -- down routed full auto 10g layermode query on if_idx 0x16000000 failed: status: 0x40480003 - no such pss keyif_info_status: 0x0Po1 ...
Hi,We are seeing the error message below on a cisco 7300 device. Now this has only appeared once but we are keen to finf out why. Cisco erro decoder does not have much to go by. It seems this error is something to do with the VTY linesSYS-3-DUP_TIMER...
Hello,We need people to evaluate a product we developed to automate the download of config's from Cisco devices and allow batch posting of IOS commands to Cisco devices. The product is called netdonkey(lite) and can be downloaded from http://www.netd...
I need to setup a port for monitoring both my vlans. I think I have the commands right but I was hoping to get feedback before doing so.monitor session 1 destintation interface fa5/3thanks
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-17-2024 06:34 PM | ||
| 11-06-2024 04:49 AM | ||
| 11-04-2024 07:57 AM | ||
| 10-24-2024 11:57 PM | ||
| 10-23-2024 06:42 AM |
| User | Count |
|---|---|
| 15 | |
| 8 | |
| 7 | |
| 5 | |
| 5 |
