Resolved! DNS on Cisco 877
How to configure Local IP(Router IP)address , gateway address for PC's to work as a DNS on PC's to access internet rather then using ISP DNS.
How to configure Local IP(Router IP)address , gateway address for PC's to work as a DNS on PC's to access internet rather then using ISP DNS.
Recently I upgrade one catalyst switch 6506 with 2xSUP720 and 2x WS-X6724-SFP with LH SFP modules . The problem is when disconnecting the optical links with the 3500XL and 2950G that was previously connected to the 6506 via an old WS-X6416-GBIC card...
Why the port of a sw 2950 change port blocking status with a loopback plug?
Hi all. I just upgraded a 3640 to 128NVRAM and upgraded flash from 16MB to 32MB.I am getting Unable to boot due to illegal DRAM configuration on bootup.Any ideas?rommon 2 > meminfoMain memory size: 48 MB in 32 bit mode.Available main memory starts a...
We are trying to setup the SNMP trap sent from sc1 interface instead of sc0 but can't find any command from the switch?Is it possible?
Hi,i have host connected to port on my swtiched network, please let me know on which and which post the host is connectedHost ip:10.1.89.501 step:core720#p 10.1.89.50(host IP)Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.1.89.50,...
I am trying to configure Management Interface on a 4506 that has a supervisor v-10GE.I followed the following stepsconfigure terminalinterface vlan 99ip address 192.168.1.245 255.255.255.0no shutdowninterface fa 3/4switchport mode accessswitchport ac...
Hi all, is there any way of protecting my network against arp poisoning attacks etc?cheersCarl
Hello,I have a 2950 switch. I start with the default Startup file (no configuration), I play with the equipment creating some vlans and when I turn off and on the switch (not saving the running-confi file)... the configuration is erased and start wit...
Hi, I am sure I can show the last changes made on a 3750 stack, but I am unable to locate the command...Any help is appreciated..Thanks in advance..
what is MSTP ? where can we use MSTP?
Hi All, I just wanted to see if this is even possible. I have a 3750 switch as the main switch at each of my outlying sites. They connect to the core via 100Mbs fiber, at the Core is a 4507 switch. On the 3750 I have 4 vlans, Guest, manageme...
Hi,I dont know much about HSRP but i have one doubt can we use HSRP in L2 switch alone to achieve redundancyThanks,Hari
Hi All,I've been asked to configure VRF's using VRF lite on our LAN. Could someone please point me in the right direction for an example of a basic setup/configuration.Best WishesSteve
Hi all,i need to setup a 1812 with the following configuration:- fastethernet 1 e 2 trunk with vlan 10,20,30,40- fastethernet 3 with vlan 10 in access mode and Priority 3- fastethernet 4 with vlan 20 in access mode and priority 4- fastethernet 5 with...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-16-2024 11:51 PM | ||
09-16-2024 06:33 PM | ||
09-12-2024 02:06 AM | ||
08-28-2024 02:25 AM |
User | Count |
---|---|
10 | |
9 | |
7 | |
6 | |
5 |