Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

network diagram:source---catalyst 7609---juniper M20---no receive.7609 connect M20 vlan is vlan404,why vlan 404 not prune.(*, 239.255.2.2), 00:02:19/stopped, RP 0.0.0.0, flags: D Incoming interface: Null, RPF nbr 0.0.0.0 Outgoing interface list: ...

Hi. Given a setup where routerA with ip add 10.0.1.1/24 on s0 which is connected to s1 of routerB which in turn has s0 with ip add of 10.0.2.1/24 connected to s1 of another router, routerC, with ip add of 10.0.2.2/24. Using tftpdnld, what should be...

Hi, My understanding of ebgp-multihop is that it increases the TTL so that we can reach for example a loopback interface whereby otherwise the packet would be dropped at the physical interface. Q: When configuring iBGP with loopback addresses why is...

hi all.here is the setup i have: ASA5510 - int e2 >port 14 on 2960sw in VLAN 40and port 14 is set to access mode.Server plugged into port 13 of same switch same vlan and set to access as well. ASA has access list to permit icmp any any echo on the e2...

SOL10 by Level 1
  • 353 Views
  • 2 replies
  • 0 Helpful votes

I wanted to move two ports in an etherchannel from blade 4 to blade 3. So I configure two ports on blade 3 for channel-group 1 mode on and I get this messageEC-5-CANNOT_BUNDLE2: Gi3/1 is not compatible with Po1 and will be suspended (trunk encap of ...

jlhainy by Level 2
  • 379 Views
  • 3 replies
  • 0 Helpful votes

Hi everybody,I have a very simple problem using RIPv1 which effectively amazed me.I tried (just for demonstration purpose) a very simple setup using 4 routers connected in line (1721+2610). They all have RIPv1 enabled. There are only classful net. a...

Hi, I want to connect my both 3560 switch togather.1stswitch:3 vlans but all server are attached to only one vlan8(ip 192.168.5.1/272ndswitch:3 Vlans but server are conneted to one vlan8(192.168.4.1/32only 1st switch is connected to internet:Requirem...

have the following config on two 3750'sswitchport trunk encapsulation dot1q switchport trunk native vlan 900 switchport trunk allowed vlan 132-135,535,900 switchport mode trunkwhen I no shut, link comes up, then down. vtp mode on core switch (one en...

OK i am trying to setup LLQ on my 2621, so i have priority on the internet (web traffic).. My net diagram is as follows.....CABLE Model........(fa0/0)-2621-(fa0/1)---switchHere is what i run into...i cannot set QOS on FA0/0 for a few reasons. #1 it i...

mikegrous by Level 3
  • 1008 Views
  • 10 replies
  • 0 Helpful votes

Hi all, if my server tags vlan packets already, what would i set my switch port to? would i just set it to an normal access port and a member of the same vlan ? i thought when you set a port as access any packets that come in normally are untagged

Hi all, Can anyon tell me the process of when say I plug a pc in one switch, and then if I unplugged it from one switch, then plugged it into another switch, how does it make sure the mac address is cleared from one port ans then added to another, is...