Switching

I have several 3560's, 3550's, 2950's and 2924's. They are all on different feature set even though they all do the same job. The only difference is that some have poe ports and some dont. c3560-i9-mz.122-20.SE4.binc3560-ipbase-mz.122-25.SEE3.binc35...

Guys,Please can someone let us kow a couple of things about this command.1. Is this command setting a percentage of the port buffer (say 14MB for TX on a WS-X6704-10GE) or a weight of the buffer space. Cisco documentation says weight, but SRND says...

Hello!i have seen this Config for IPv6:frame-relay map ipv6 2001:CC5E:4321:ABCD::10/64 110frame-relay map ipv6 FE80::CCE3:1FFF:FEB7:0 110THE QUESTION:What is this:FE80::CCE3:1FFF:FEB7:0?how can i find it?10xs

Hi all,I'm kind of hoping that someone here will be able to help me.I'm trying to do diagnostics for a 6509. Now i log onto the supervisor card of the 6509 and get the following output:System Bootstrap, Version 7.1(1)Copyright © 1994-2001 by cisco S...

I am in the process of troubleshooting a printer which looses connectivity in the evening. I need to prove that it is not a network connectivity. But this is what I find.When I removed the network connection, i can see it lost "pings" but nothing sho...

What is the order of operation for PBR and "ip tcp adjust-mss."I have two ISP's (i.e. 2 default routes) and need to force pbr matched packets to use one ISP. When PBR is configured on the routers ingress interface, I get web browsing behavior that ...

Problem in C3560 with IP-Phone avaya,Plsi want to ping form pc to ip phone avaya [1608 series] but cann't work and this config on switch C3560no aaa new-modelip subnet-zeroip routinginterface FastEthernet0/2switchport access vlan 10switchport trunk e...

Hello,is it possible to read out the temperature value of a WS-C3560G-24TS via SNMP. (I fear it's not)If yes, what's the OID?I only found Oid : 1.3.6.1.4.1.9.9.13.1.3.1.3.1005 (ciscoEnvMonTemperatureStatusValue.1005 )Value: 1

Hello, I have a problem with bidirectional NAT on cisco IOS routers.I need to convert the next telnet session via NAT :Client is on Outside interface :Client 172.16.186.100 => Telnet 172.16.186.11 (2501) => Cisco 1721 (fasteth0.1) => Static translate...

If I have an IP routing enabled 3750G that has 2 different L3 paths to a destination and OSPF recognizes these 2 equal cost paths, does CEF automatically load balance on these links or does OSPF use some load-balancing mechanism?

Hi,I have several 2960's and a 3750. Currently I have created several VLAN's, and the 3750 is configured for intervlan routing. I would like to use the 3750 for DHCP. How can I create multiple pools and ensure ip addresses are allocated to the right ...

After installation of '2960G 48 ports' all machines with 100Mbit cards had big problems to transfer data over the network. Servers and desktops/laptops are on the same switch. I tried all possible variants of connections on both sides auto/100/half/...

IOS 12.2(25)EWA, Config Guide page 33-4: "You cannot apply more than one IP access list and one MAC address list to a layer2 interface."Does it really mean this, or does it mean one in each direction? If I put an ip access-group XYZ in and an ip acc...

Hi,Network newbie here!What is the maximum number of segments I can have on a 100BaseTX network?I would like to network call entry devices for elevators in a high rise building. There would be a maximum of say of 8 call entry devices per floor but t...