Switching

Hi guysPlease can you assist i am presently trying to recover an 1841 from rommon mode by using xmodem but it keeps giving the following, Will paste in actual text from router"rommon 12 > xmodem -c c1841-ipbasek9-mz.124-11.XJ4.binDo not start the sen...

I am looking for a Cisco switch which can be compared to Enterasys A2H124-24FX SecureStack A2 with 24 100Base-FX Ports via MTRJPhysical Ports24 100Base-FX MTRJ ports2 SFP GBIC ports2 10/100/1000 ports for uplinks or stacking ports1 DB9 console port1 ...

All, Im trying to do the following, without success at this point. I have a laptop, 3560 switch, and ACS v3.3. I have the port my laptop is plugged into to do dot1x. If you login fine, you get on the trusted network. If not, you get dumped into t...

Dear Experts ,Please find the attached network diagram.we want to do load-balancing between E1's which was mentioned in the diagram.Generally , how to achieve load-balancing using HSRP ?I know we can go for MHSRP ,, but we do not want to use MHSRP.An...

Hi!I would like to send all events to begin with. But the Eventsmanager doesnt get any syslog activity. Is there other steps i need to do on the switch other then ->Logging myhostname?If i want to monitor almost every event is default settiing good f...

do i need to add it as a client mode or transparent than to to server mode,but i think as transparent the switch does save the vlans10xs

i want to know if there is a more simple way to alow VPN trafic on a vlanthe way i'm dooing it now is just alowing varius ports depending on what is neededand that can lead to some trouble because when i get a user that has a different cliend/port i ...

I need my 6500 VSS supervisor - VS-C6509E-S720-10G to support an IPT network (QOS features, etc). What IOS should I be going with?IP Services, Adv Ent Services, IOS Adv IP services or advanced enterprise services?

I have a question of QoS trust behavior, I am not sure if what I remember is correct.If I config mls qos trust cos, what will be done for dscp? will the dscp be remarked with the config of "mls qos map cos-dscp"? and for mls qos trust dscp, will the ...

Hi allIs there any situation i would configure a layer 2 Vlan at the distribution layer. I am using layer 3 sw at the distribution layer. If yes , may i know the reason for doing that.What i usually do is to configure layer 2 vlan at teh access switc...

We have been running an 1841 router with one T1 interface and one FaE interface for over 1 year now with no problems. Recently we added a 2nd T1 interface and bonded it via multikink PPP with the 1st T1 interface. Almost immediately we started expe...

I have a brand new 3550 set up in its own VTP domain with administrative VLAN 16. My switch is connected to my other VTP Domain via fiber where I have a common VLAN in both VTP Domains to allow communication. I have full communications between VTP Do...

Just inherited a network full of legacy CatOS and IOS switches ,a Lot of VTP and in excess of 100 VLANs...trying to size it...could anyone assist on a quick note what could do to identify 1 Trunk utilisation-On CATOS and IOS 2 VTP issuesAny other tro...

Hi,I am facing problem with 2821 router where if i login to the console able to ping DNS and gateway but unable to ping the dns as well access internet from host located on 10.43.12.0 network i have attached the config for ref

Hello,I have some questions about routing and switching design.I have old Cisco network (Catalyst 4006, ...)With several end point connected with fiber .Today i have some network loop (spanning tree is in use).I have some questions about change in my...