Hi, is there a way to remove/delete the “no platform punt-keepalive disable-kernel-core” “no platform punt-keepalive settings” from my running config without rebooting? I am currently working on 3850, thank you in advance example below:no service pa...
Forum Posts
Hey guys, I have a SG200-50P that I bought used. Yesterday I finally wanted to migrate all of my infrastructure to it. I connected a door phone (Fanvil i10, not that it matters) to it. It powered up (POE) and got an IP. So all working. But it was in ...
I have a Cisco IE 3300 switch installed with two 480w AC to DC power supplies. Is it possible for them to be used in a active/active mode?
Hello,Two of our SG350--28MP switches are connected by two cables.We created a LAG for two switchports on both switches.The LAG functions until we restart one of the switches.The LAG link is down after the restart.When we unplug and replug the two LA...
I am trying to overwrite the startup config file on a cisco 2960 switch. I am issuing the following command copy tftp: startup-config I go through the prompts and I am getting the following error #copy tftp: startup-configAddress or name of rem...
Hello folks.I'm investigating an incident with two 3850-24XS-E switches configured as a stack. Both switches have remained online during this incident. The #2 switch in the stack order is currently the active switch, and has been for 10 months. A wee...
Am looking at a c9300 24port switch all ports should be 10g also stacking features should be included please give me a workable part number
Seeking IE 3300 TACACS sample configuration - for code 16.12.03Question - Are there any new requirements for TACACS configuration with this code version noted above (16.12.03)? We have zero issues with devices running 15.2.7 IOS Current configurati...
I have 2 9200-48P switches with network-advantage license on them and I can't get to connect to each other using 10-gigabit SFP. They are running SW version 17.03.04 and these are the first switches we are deploying with SW version 17. If I replace t...
Resolved! ERROR FW[MOD 05]: LOG - WSC6509-E
Hello Guys, Someone know what bout this issue is? 16:13:35.829 FW[MOD 05]: radian_monitor_pll:: port_num[4] unit[1] bcmport[5] : PLL reset failed - xlport_xgxs_status_gen_reg = 0x0 xlport_xgxs_ctrl_reg = 0xFF80016:13:37.589 FW[MOD 05]: radian_monitor...
Hello,I have a problem which the violation count of one of my interfaces.The port-security of the interface is disabled, but i have a violation count of 54.I thought, that it isnt possible for the violation count to rise, if the port-security is disa...
I am trying to understand how to enable logs on my switch. I know the command "show logs" or "show logging" is meant to provide that functionality, but I need logs from a specific time period specifically the past month. I also would like to understa...
Resolved! Unable to login to SG200-26
Hi,I recently aquired a SG200 26, as a NOOB(be warned) I'm trying to login to the router.As for the moment I've connected the router to my laptop and try to acces it using this adress: 192.168.1.254 with timeout as a result.I've tried to reset the sw...
One of the computer take its ip by dhcp server but we created reservations for this ip with "ip source binding ..." command on cisco switch. However user didn't authenticate his PC and when i checked logs i saw "%SW_DAI-4-DHCP_SNOOPING_DENY:" error m...
Resolved! Recovering a Cisco 9600R
Hi AllI am working on some DR documentation for the recovery of a cat 9606R switch with dual supervisors running in stackwise virtual, quad supI need to imagine a failure of one of the chassis for example where they wont boot and I have been delivere...
