Switching

i have a 3750 Giga speed switch,each port is capable of 1 gb portbut when i do inventory using ciscoworks,it shows me that some ports are not functioning properly.some ports are showing 10/100 mbps

PC-A IP=10.1.1.1 +--+[e0/0:10.1.1.5 RouterA s0/0:195.1.1.4]===V35===[s0:195.1.1.10 RouterB 152.1.1.1:e0]+--+[e0:RouterC 152.1.1.2](Please see attachment for a better diagram)From any device on the network, I can ping each other OK.However, my questi...

I noticed that my Cisco 831 is showing 0 bits/second on all FastEthernet ports but the Ethernet ports display bits/second. Is there a reason for this difference? Can this be changed and if it is changed what is the implications if any?Thanks.

I work in a college and given below are the specifications and questionswe have lease line (256 kbps), modem (keymile lecar), cisco router (cisco 1721), proxy server (winxpsp2 running winproxy v 2.1R2h), Fortinet firewall (fortigate 60).I face the fo...

I have setup an 1811w in our office with multiple vlans, NAT, 802.11g, and VPN. I pretty much have everything working the way I would like, except for one thing. We have 2 static IP addresses assigned by our cable internet company. We have 2 termi...

Regarding the question below, can someone confirm how you determine which route it would take ? If you write the next hop information in binary to compare against the target route, you have to do that for "via 153.2.220.2", for example ? Is that corr...

Greetings, New here. Please bear with me, I have been in computers as a career for 8 years, but I am new to cisco routers.I am trying to configure this router. It is a 1721 with a wic t1-dsu card in it. What I would like to do is use the sdm to confi...

Can someone clarify what I am missing ?(3) routers connected. Please find attached the file showing 'show run' from all three routers and diagram.I try to ping from RouterC (150.1.1.2) to workstation 152.1.1.3 and it times out.On RouterB I put a defa...

I'm working with a Cisco 1700 Router. I need to establish some static port mappings. I am able to telnet into the router, can enter enable mode, and then conf mode. My question is: How do I add a static port mapping. From the research I've done, ...

we are running client - server application in which server send message using destination port 1010 to client. we are using services of different ISP to route our packet upto destination that's ok . Now one of our new ISP's using DSL to connect our ...

I'm new to Cisco and hoping to implement a large Cisco solution. Unfortunately we're not in the position to hire an expert so I'm seeking some much needed advice!The general plan for phase 1 would be:A router with 9 interface cards, that will have a ...

this is the reading i currently get when i boot the switch(3548-XL-EN)...how do i load new ios into flash.....C3500XL Boot Loader (C3500-HBOOT-M) Version 12.0(5.2)XU, MAINTENANCE INTERIM SOFTWARECompiled Mon 17-Jul-00 18:42 by ayounes starting...Bas...

I am associated with a printing business. 12 computer stations, 12 Commercial printers and A website. Need each computer able to talk to each printer. Can be up to 120 feet between switches and computers,printers. Need to evaluate switches, router...

Hi all,I have two 3550's connected in a stack using gig ports. I wanna moniter port fa0/1 of switch one and fa0/1 of switch two traffic on port fa0/4 of switch one. I wanna to know if i can configure RSPAN to do that. Please let me know how to do it...

Below is the router and interface configuration of two 3725 routers. The problem is, I'm not able to ping PC connected to each router (PC1 connected to Router_01 and PC2 connected to Router_02, (Router_01 directly connected to Router_02). I'm able ...