I wanted to ask if anybody could point me the right direction how to configure a 2811 router with two default gateways. I bought another port so I have two ethernets coming in and one going out to handle this.Thanks!
I wanted to ask if anybody could point me the right direction how to configure a 2811 router with two default gateways. I bought another port so I have two ethernets coming in and one going out to handle this.Thanks!
I have a 1760 Series Router with a Serial Interface that randomly goes up and down. According to our provider, they can find nothing wrong with the line. It is configured with a single Ethernet WIC (E0), and a single WAN Wic Card (S0). Configurati...
I'm trying to have users on an outside LAN (10.1.1.x) browse or use telnet services via PAT to an inside LAN (192.168.1.x). So a user browsing 'http://10.1.1.5:50000' would reach the web server on port 80 at 192.168.1.50.Here's the current rules. I'v...
We're NATing the destination addresses, using the ip NAT outside source static command and sending the NATed packets to a specific address through the defaut route (192.168.3.2). Does anybody happen to know if we can use the native address of the def...
Hi,Though its a very silly and basic question.....But i don't know it.How can i connect the fibre cable on the pc?????????Do we have some ethernet cards available for the same??????????????//Looking for response on ASAP.Thanks
HiI have a question in which i hope somebody can helpI have 2 router if I configure 10.1.1.1 255.0.0.0 on e0 for router1 and 10.1.1.2 255.0.0.0 on e0 for router2. After doing the above , I can ping both routers BUTi decide to change router1 e0 to 10....
A Chairde, I am trying to ping from Blade 3 (FastEthernet) port to Blade 1 (Fibre) on a 7609.From Console, I can ping both , but When source is FE and destination is Fibre , I cannot. I need to run NMAP on a Fibre Interface to see ports ope...
Hi,Iam integrating firewalls into our network which has connectivity to other vendors using Border routers running BGP. The distribution of these learned routes into our network is by OSPF. We are running OSPF in all switches to learn the routes betw...
Hi there,I've just updated my 837 ADSL router to IOS 12.3(11)T3, which is supposed to enable a second Ethernet port (using the physical FastEthernet 4 port) for DMZ use.I've successfully flashed the device, and followed the instructions:>Router(confi...
In our LAN basing the cisco switch 2950-24T, ALL PC can work good, but the powermac can't, they can't see together or can see few but can't connection,whether need to open Appletalk Protocal in this switch? but i can't see any about this command when...
I have a 1720 router and a WIC-1ENET when i first installed the Card it worked fine but my software package didnt have inter-vlan communication so i have upgraded to several different Options (i picked out software that cisco said could work with my ...
I am a student employee at a research lab and we are trying to set up a local network for file sharing between scientists. Our workstations are connected to a hub then to a cisco 2620 router that is connected to our headquarters by a T1 line.We do n...
I think I have a problem with either my router.I can not seem to connect to any ftp sites. I had a power failure a week or so back that out lasted my UPS. Ever since then I have been unable to ftp out. I am not sure if my router has lost some sett...
Hi,We have a cisco 1700 series and two 2500 series these routers connect our three branches using leased line. presently each branches have different subnet. eg. Branch1 - 192.168.0.0/255.255.255.240, Branch 2 - 192.168.0.32/255.255.255.240, Branch 3...
What I must configure when I will get a banner, before I loged in over SSH?
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
09-12-2024 02:06 AM | ||
09-10-2024 10:07 AM | ||
09-03-2024 06:59 AM | ||
09-03-2024 12:56 AM |
User | Count |
---|---|
9 | |
8 | |
8 | |
7 | |
5 |