Hello Guys, I was Reading documentation for latest IOS-XE (Bengaluru) where i saw support for SVL with VxLAN on Cisco Catalyst 9500I could not find any documentation which shows integration between the two and what factors needs to be taken into cons...
Forum Posts
Resolved! NX-OS upgrade issue
Hi all! So I did a impact check before upgrading (show install all impact nxos nxos.9.3.8.bin) a 9200 series device on the nx-os file that I've downloaded. But I got a message that I haven't seen berfore and it worries me I've attached the output fr...
How many GRE Tunnels supported on Catalyst 9300 switches (C9300-24T-A)?
Resolved! C3560X-24P-E IP service
Hallo i got 4 C3560X-24P-E that i need OSPF on. so i looked up the IP service ISO for the switch but i cant find it anywhere on cisco software download. i looked up on the data sheet that it is suppore. (https://www.cisco.com/c/en/us/products/collate...
When i tried to ping the pc on 1.2 from pc 1.1, it works fine, i get a reply and 0% lossbut seeing the color of the cable on Fa0/1 just making me confused (even after i used the skipped time feature), does that mean it isn't fully connected? What if ...
Hello, I am trying to get a UCS Fabric Connect switch to work with Radius. I have NPS set up on a windows server and have set the instances Secret key along with the Host IP of the device. I set the Radius as the Native authentication and created a d...
Hello,having a plain L2 network with almost 60 (sometimes older) switches. On all switches rapid pvst is configured, VTP is also configured. No comments please The "VTP-Server" is an 3750g Stack with 12.2(55)SE1. There are 128 Vlan's configured. Now ...
Hello Community, In the old Catalyst 3750, there was the remote command switch-number command to execute a command from the master switch to a member switch.Now, I have a Catalyst 3850 stack with version 16.12.5b and I cannot find this command. Howev...
HiI accidentally changed the boot to point to the wrong file on catalyst 9300 and its not accesible, is it easy enough to recover and get it booting to the image again please.?also i recently tftp'd an image to a 9300 17.3.4 and installed and booted ...
Greetings to everyone I need your technical advise based your knowledge and experience of the the best practice in configuring our new 2130 as transparent mode FWs inline between core switch of HQ and Core switch of remote sites. The core switches s...
Hola!tengo un Switch IE4010, donde van conectados dos servidores advantech con tarjeta para permitir PRP y PTPtengo el siguiente mensaje en el switchSep 30 23:04:05: %SW_MATM-4-MACFLAP_NOTIF: Host 6ad8.4f10.ba06 in vlan 1 is flapping between port Gi...
We track network switch inventory by creating an inventory number and associating it to a switch serial number. A sticker is then generated with that inventory number on it and is stuck to the side of the switch. I am trying to devise a way to config...
Dear All, We're planning add our 9300 into cisco smart account . I've also referred below cisco link - how to setup cisco smart account and add catalyst device into my account. Apart from creating new cisco smart portal account and activating , I'v...
Hi AllWould like to check out is it feasible to do both end back-to-back etherchannel between these devicea pair of cisco FTD in active-passive HA setup connecting catalyst switch doing VSS.No cross connection, meanFW01 g0/1- SW01 g0/1,FW02 g0/1- SW0...
I would like to configure a device in my topology to have a dynamic IP. The device a Nexus Titanium, which I assume is similar to or the same as a NXOS7. I'm totally unfamiliar with configuring Nexus devices, but trying to learn the basics. So far I ...
