Hello,I have a N3K-C3064PQ-10GX and i have 350 Vlans on it and i am monitoring it from 2x server (one of them is observium and other one is prtg) and i have applied an acl on my uplink to drop snmp packets and snmptrap packet except for my trusted ip...
Forum Posts
Greetings, After updating the switch through the web console with c2960x-universalk9-tar.152-4.E8.tar we no longer have the Web Console.It initially gave a 404, but after reboot of switch it just loops back to the "Cisco Systems" default web page. An...
Hello,I have 2 questions about the C9200L-24T-4X.1. Does the uplink ports supports 1G and 10GB and I could mix them? Also 2 uplink port connect via 1GBit and 2 uplink ports with 10GBit? 2. I have a really poor multimode fibre... it is maybe only OM1 ...
Hi Guys I am trying to report an issue to Cisco TAC but I cant get the serial number via the CLI. The GUI says "System processes are starting, please wait." so i cant log in that way. It has been like that for 24 hours.admin@FP-FMC-01:~$ show invento...
Hello.Have problem with connecting VLANs. Devices connected via Fa3 (router) and Gi8(switch), Gi7(switch) client device.Router config:interface FastEthernet3 description << LAN L2 >> switchport mode trunk no ip address ! interface Vlan1 description <...
Hi Cisco 4500-X16 switch configured as VSS,but Active and Standby is not functioning properly.After few minutes not appearing in the "#show switch virtual role" list. VSS-CORE#sh switch virtual roExecuting the command on VSS member switch role = ...
Hi,The devices connected to 2960 are not getting ip addresses from windows dhcp server. IP helper is already configured. Below is the brief core and access switches config. Core:interface Port-channel1description ** Uplink to Access Switches **switch...
Resolved! ACL not working as intended
I created a new network within our organization that has an entire new /8 and is linked between a routing protocol adjacency between this new network and the backbone area. This new /8 called for a wireless guest network that would only need access t...
HiI have a 6509 running 12.2(33)SXI4 that has an interface config that I have never seen before:interface TenGigabitEthernet3/2 description hv Sw-2-1 switchport switchport trunk encapsulation dot1q switchport trunk native vlan 308 switchport trunk al...
Hello, I have the following PoE devices running in a daisy-chain: - DIGITUS PoE+ Injector 802.3at GbE 60W as a power source- Cisco WAP-361 (POE PD and PSE, running on PoE without a dedicated power supply)- Cisco SG250-08 (POE PD running on PoE from W...
Hi all,when i run the commandsh cdp nei gigabitEthernet 9/26Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge S - Switch, H - Host, I - IGMP, r - Repeater, P - PhoneDevice ID Local Intrfce Holdtme ...
I own a CISCO RV340 Router. This Router was purchased via Amazon India. I am facing a problem in the LINK/ACT LED display on the port of LAN-1 in the router. The LAN-1 port of the RV340 is connected to an unmanaged Switch and in turn the Switch rende...
I am new to this forum so please forgive any missteps I may make as I get used to the rules and etiquette. I just purchased two 350x-10s for a private network I am building. Here is what I am trying to accomplish:Switch 1- I want to exclude any mult...
Hello, We are currently paying for 350Mbps and are noticing a lot of our issues surrounding speed on our applications related to internet speeds. The 1010 is rated for these speeds but I am only using one port on it - would it be possible to upgrade ...
Resolved! Nexus 9k switch remote access
HI I have a pair of 9k switches running both layer 3 and 2, we are low on ports so I am trying to introduce another9k switch but only as a pure layer 2 switch. I have an existing vlan that I will us trunk/port chnnels to connect the new switch to th...
