I am curious about configuring bandwidth restrictions for specific VLANs through a switch. For example, restricting a guest Wi-Fi VLAN to 10 Mbps. While this can typically be done via a wireless controller, the customer requires this to be configured...
Forum Posts
i experts, I'm getting this repeated notification daily since 3 days and now I received a complains that the IP phones keep getting restarted in the switch location offices. logs from core switch : Sep 26 06:34:26.664: %SFF8472-5-THRESHOLD_VIOLATION...
I've got a VSS pair of 6880-Xs in a VSS pair running 15.2(1)SY6 as the network core switch connecting to various IDFs with a pair of fiber in a portchannel. We also have some monitoring software that pings the IDF switches periodically go see if they...
If there are 2 switches stacked uplinks given to each 2 switches with 2 ports each, say eg port 47 & 48.Port 47 & 48 are created LACP for each switch Then what is the use of stacking here for redundancy?I am newbie. Please explain.
cisco nexus 9000 c93180yc-ex SNMP configuration for whatsup gold 24.0 build 2096 We are getting credentials error after configuring the SNMP for Whatsup gold.
Hi,I have a quick question regarding the Stackwise configuration for 4 Catalyst 9300 switches. In terms of connecting them, which scenario would be correct:Connect switch 1 stack port 2 to switch 4 stack port 1 ORConnect switch 1 stack port 1 to swit...
Hi everyone , i am quite new . I have been stuck up from quite few days . i have to implement a solution for the below requirement . 1) i have 15 devices with same ip address ( ip address is hard coded inside and can not e changed ).2) each device...
Greetings! Let me start by saying I am NOT a network engineer, so I am just now learning how to configure VLANs on switches.What I want to do is to set up two separate VLANs on a SG-200 switch that are totally isolated from each other, replacing two...
Resolved! switch: CCCCCCCCCCxmodem:: I/O error
hello I goofed and uploaded a new image to my Cisco 3750.I deleted the prior image and set the boot flash statement and then used the command boot system flash: old image/new image This caused me to enter into switch: mode I have tried various recove...
I know this has been discussed, but my situation may be more unique. We were having issues with a 24 port POE 3850 not being able to power all necessary cameras (13 I believe). It has two 710w power supplies which is more than enough for this applica...
Good afternoon everyone,Came across a curiosity as I was doing some network hardening for my campus network. I started blanketing access switch interfaces, spread across many vlans, with a configuration that included "ip verify source"~~ex.interface ...
I have been task to turn a immature network into something that looks more standardized. I wanted to create a Network Design with Collapse Distro & Core with a single WAN connection and two core/distro switches. Question 1.) For FHRP, what connection...
I have a question about HSRP and ACL configuration on Cisco 4506 and 4506E switches.Initially, without HSRP enabled, I configured the following ACL on the VLAN 55 interface:Extended IP access list vlan5510 permit ip any 192.168.104.32 0.0.0.1520 per...
We are in the process of replacing a legacy Juniper Core switch with a 2 stack Cisco 9300 configuration.The VM Hosts within the environment are all configured in the current Vlan 1 on the Juniper switch.We are trunking to these hosts.We have the foll...
Hello to all, 877 have just brought a shindy but I have problems to form the fastethernet, on having tried to form an ip address it(he,she) appears: IP addresses may not be configured on L2 links.Since I can solve it? I have tried to use the SDM but ...
