Activity in Technology and Support
Cisco NDO API backward compatibility
Is the NDO API backward compatible?I have two Nexus Dashboard deployments for different sites:Nexus Dashboard 3.2.1e (newer)Nexus Dashboard 2.1.2d (older)The following API works on the newer version but does not work on 2.1.2d:GET /mso/api/v1/nodesIs...
Cisco ASA 5508-X with FirePOWER fails to deploy policy
This started suddenly, without any configuration changes on our end. I've noticed that Cisco's recently published SRU packages have dropped significantly in file size (from the usual ~40-50MB down to ~19MB in the last 3 consequent releases, and this ...
MPLS - No Label versus Pop in the output of show mpls forwarding-table
Hello, everyone.I understand that when a router receives a packet and the output of show mpls forwarding-table lists No Label as the action, the router removes all labels in the stack and forwards the packet as a regular IP packet.The 2.2.2.2/32 rout...
Add new MDS switch to an existing SAN Fiber Channel Network Nexus5548
Hi, We have a SAN network of 2x Nexus 5548 switches with Fiber Channel. Both Nexus are linked together with San port-channel FC ISL trunk links, and we are using a single VSAN. Topology is as follows: Nexus-5548-A < ----- > Nexus-5548-B Initiators (H...
increase Cisco Quad camera speaker tracking speed
We are using a Cisco Codec EQ system with a Quad Camera, PTZ camera, and IP Microphone Pro, running firmware version CE 26.5.2.2. The system is registered locally to CUCM.The customer wants to know if it is possible to make the speaker tracking faste...
Resolved! Spare AP require license
We are planning to buy a few spare AP C9120 just in case any APs go faulty. Do we have to buy a license for the spare APs? or when replacing the AP, it will take the license of the faulty one?we have DNA-C and C9800 WLC
2 Users out of 700 Unable to establish or Join webex calls when On VPN
I have a peculiar situation with just 2 users so far reporting that they are unable to establish or Join webex calls/meetings when on VPN.Both users are currently working from abroad in EU.1 User can't establish a call no matter if he is connected to...
Resolved! Upgrading Cisco 8841 from Enterprise SIP to MPP via TFTP fails
Hello,I have Cisco 8841 model phones, which currently have SIP firmware installed. Now, I want to upgrade all of them to MPP/3PCC firmware.However, when I try to do this via Tftpd64, which used to work before, I am now unable to upgrade the firmware....
Does MPLS perform ECMP over a mix of labelled and non-labeled paths?
Hello, everyone.I am reading the MPLS Fundamentals book which states that If a prefix is reachable via a mix of labeled and unlabeled (IP) paths, Cisco IOS does not consider the unlabeled paths for load-balancing labeled packets.This sort of counters...
SNMP at 5s and 6s
Hi There,Was wondering if someone has come across this before.I'm polling a couple very limited SNMP OIDs (ifHCInOctets/ifHCOutOctets of some interfaces) at high intervals on Catalyst 9300 class switches.At 5s, the ifHCInOctets/ifHCOutOctets is very ...
A New Chapter for DevNet Sandbox
Hi @All We have some news to share. Please read the message below:Beginning August 1st, the current Sandbox platform will temporarily transition offline as we build something entirely new from the ground up, a platform designed to deliver a more focu...
ISE Posture always open Redirect Page Even Posture Agent Compliant
Hi,I done installed ISE posture agent on window 11, I tried use CPP and installed manually methods, both are working, posture can scan and inform status compliant. But, problem is when user reboot or power PC on -> login, posture always popup the red...
Has anyone completed a Wi-Fi 7 (802.11be) deployment using DNA Center
Hello everyone,I am currently working on a Wi-Fi 7 Proof of Concept using:Cisco Catalyst Center 2.3.7Cisco Catalyst 9800-40 WLCIOS-XE 17.18.3Cisco CW9176 Access PointsThe WLC has already been upgraded to IOS-XE 17.18.3.The existing wireless environme...
C9124 Access Point is unable to join 9800 WLC
Hello TeamThis is regarding C9124 access point where I have existing WLC UP and running and all other access points are working finr and I am trying to associate two new C9124 access points to it.I see that these two access points of C9124 are not jo...
Cisco Secure Client stuck AFTER correct Authentication
I can't connect to my entreprise VPN using Cisco Secure Client on windows 10 enterprise. Few days ago I succeeded multiple times.Description of the steps:1 - launching Cisco Secure Client (I tried with/without "As Admin")2 - the correct VPN name is d...
| User | Helpful Count |
|---|---|
| 162 | |
| 76 | |
| 51 | |
| 49 | |
| 48 |
