Ask Me Anything Event Welcome to the Cisco UCS C-Series Servers session! Whether you're setting up your first server or optimizing an existing deployment, this event is your one-stop destination for everything UCS C-Series. Our expert engineers, P...
Hello,Is it possible to disable a servers vNIC or vHBA? I was unable to find an option to do this via the GUI, maybe CLI? The reason is I would like to ensure the failover mechanisms and paths are correctly configured...Thanks
Hi All, Is there a recommended version of UCSX Blade Firmware on Intersight? Because intersight in the cloud does not display the recommended version, my Intersight PAV(1.0.9-561), UCSX 210Cm6(5.0(2e)), FI: 6454(4.2(3C)) Thanks.
I've trailing some C220 M5 servers in my UCS Mini (with B200 M4s) home lab and just wanted to clarify the right disk and boot policy settings for this setup. The servers have a UCS-MSTOR-M2 module with 240GB SSD and also a UCSC-SAS-M5 controller with...
So in my setup I have a disjointed network setup Vlan 1 is my core business and vlan 902 is for my iSCSI I have no issus connecting to vlan 902 and the blades themselves I have been able to have connect to the Vlan 1 uplink properly. I have Vmware E...
I have a C240 M4 running ESXi version 6.7.0 (latest version as of Aug 9th, 2023). I need to pass through _both_ of the USB ports on the back of the server to a VM that is on that ESXi host.I was able to configure pass through for USB port #2, but no ...
Is this possible? I've tried multiple combinations of Get-UcsFabricNetGroup & Get-UcsVnicTemplate and cannot seem to get this to work. Both UCS commands produce results, I just can't figger out how to get the parent of a specific UCS Fabric Net Group...
Hello, beginner here! I recently purchased a cisco ucs c220 m3 LFF. I'm trying to install proxmox on this server, but the installer fails to find a support hard disk. When I look in the bios, I dont see the ssd (Sata) I inserted either, but the green...
I'm not getting any VGA or console output for the bios on several ENCS5412/K9. Once in a while I do get output but it takes literally over a half hour. I have several of them and they all do the same thing.
HiI'm wondering if I can connect the 2 GB Ethernet ports (LAN1 and LAN2) on my FI and configure them as server port in UCS manager or I have to buy an optional PCIe card?I'm asking you this because the 4 ports on my Modular LAN-on-motherboard (mLOM) ...
I have a new UCSC-C220-M5SX configured in my lab loaded with Esxi, 2 Socket 512GB RAM. Even though utilization is below 25%, FAN makes loud noise. Fan policies are correctly set, logs are clean, tried upgrading firmware to 4.2(3g) ,so far not much o...
We are using MECM to image our UCS devices with Windows Server 2019 and are frequently encountering an error during the phase where it lays down the OS. It sees the Windows partitions and lays down the files on that partition, but fails when it tries...
Hi guys!! I have a UCS C220 working properly, but would like to access in CIMC interface and I don´t have the corret user and password. What is the best way to reset that? regards,
is there comand line to attach iso to kvm on B series server? i am trying to attach iso to kvm with command line
hi We have a UCS C220 server on which we are running CUCM and when the power off and power on again the server's power button turns amber and everything goes down. We would have to physically turn on the power button and access the VMware and start...
I am searching for an option to attach ISO file from remote file share to UCS KVM console so that I can use it to install an operating system. After activating virtual devices in the KVM console, I'm only able to attach ISO file only from the local m...
