HiIam unable to locate installation / setup guide for fresh installation of C260 M2 for PCCE.Someone do direct me with appropriate links . Also more info on CUCM licensing for setting up on C260 M2Thanks in advance
-
Buying Recommendation
(18) -
Call Control
(1) -
Cisco ACI
(2) -
Cisco Bugs
(2) -
Cisco Cafe
(5) -
Cisco Intersight
(1) -
Cisco Software
(1) -
Cisco.com Idea Center
(1) -
Collaboration Endpoints
(1) -
Collaboration Solutions
(2) -
Community Feedback Forum
(6) -
Community Ideas
(5) -
Conferencing
(1) -
CSC Content with No Valid Community to Post
(1) -
CUCM
(1) -
Data Center
(2) -
Data Center Networking
(1) -
HyperFlex
(142) -
Identity Services Engine (ISE)
(2) -
ISR 4000 Series
(1) -
LAN
(1) -
LAN Switching
(3) -
Network Management
(2) -
Online Chat Support
(1) -
Other
(1) -
Other Collaboration Applications
(7) -
Other Collaboration Topics
(3) -
Other IP Telephony
(2) -
Other Networking
(1) -
Other Switches
(2) -
Other Switching
(4) -
Other Unified Communications
(12) -
Other Unified Computing System
(698) -
Routing
(1) -
Server Networking
(1) -
Small Business Network and Smart Storage
(1) -
Small Business Routers
(1) -
Small Business Support Service
(1) -
Storage Networking
(1) -
Switching
(1) -
UC Applications
(8) -
UC Migration
(1) -
UCS Advantage Series
(9) -
UCS Central
(61) -
UCS Director
(19) -
UCS Manager
(392) -
UCS Networking and Storage
(192) -
UCS PowerTool
(48) -
UCS Solutions
(152) -
Unified Communications
(16) -
Unified Computing
(2) -
Unified Computing System (UCS)
(6,553) -
VDI
(3) -
Voice Gateways
(1) -
Wireless LAN Controller
(1)
- « Previous « Previous
- Next » Next »
Forum Posts
Can someone help me in configuring multicast policy in UCS.I have a redhat cluster heartbeat on vlan 300. I have configured a multicast policy and applied to that vlan.I'm not sure i have configured correctly:IGMP Snooping state: enabledIGMP snooping...
Resolved! Question on Call Home
All-Knowing Contributors! I am configuring call home on our system and I see we need profiles setup. I inherited this system and the default profile is setup and it seems to only have the alert group "Normal" assigned to it. According to the document...
Hi,We have 2 UCS C210M2 servers. Each UCS has 10 HDD in it. So there are a total of 20 HDD on both the UCS C210M2 servers. UCS-1 is the primary one and UCS-2 acts as the redundant one. Both the UCS servers are on production. ESXi 4.0 is installed on ...
Resolved! UCS Central - SSL Certificates
Where can I find documentation regarding using an SSL cert with UCS central?
Here's my persistent fault (Severity=Warning) in Fault Summary: Here's what I get when I click on the green triangle icon in the Fault Summary: I get nothing. So I can't address the fault.It shows up under the associated Service Profile as well...
With Anees Mohammed and Viral Bhutta Deploying Cisco FabricPath in Data Center Network FabricPathWelcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about the Cisco FabricPath with Cis...
What is the required MDS code level needed to support FC Port-Channeling/Trunking on a 9222i, 9148, or 9509/9513 w/ Gen2 line cards to UCS 1.4(3)?I know the fport-channel-trunk feature is needed and was released in MDS 4.2 code but I have seen docume...
hello,Now I have UCS C220 M3s servers, new installation.the factory defualt CIMC version on my servers is 1.4.7b..i made RAID on all my UCS servers, succeeded. and then i upgraded the CIMC and the BIOS version using huu 1.5.1b.but after the upgrade,...
Resolved! Enable HBA in Service Profile by default
Hi,Was hoping you could help. We have a UCS system running firmware 1.3(1) and are using QLogic CNAs for our HBA & LAN connectivity.I was wondering if there was a way in the BIOS (or wherever) Policy to enable the HBAs by default as each time we ass...
Hi,I have configured a few Cisco UC and UCS with VMware deployments already. Usually all the UC appos are on the same IP range so just configure VMware NICs in Active / Standby with no VLAN tagging and configure the LAN switchports as access ports.I ...
Resolved! C240M3 Shared LOM Ext
Hi,Configuring a new C240 and have noticed there is another option in the CIMC config page called "Shared LOM Ext". From reading guides this seems to suggest that I can share the CICM Management access with any of the LOM and also any of the Cisco VI...
Hi, allI'm new to UCS server, so please guide me kindlywhat the problem is..when I try to launch vKVM to install esxi, the kvm console window is not shown.However, I can see the javaw.exe proccess running. I hava tested with java7, java6, and earlier...
HiI gets this faults when I associate a new blade or boots a blade in one of my UCS Chassis: <faultInst ack="no" cause="thermal-problem" changeSet="" code="F0411" created="2013-05-24T08:11:52" descr="Thermal condition on chassis 3 cause:Local IOM:IOM...
I opened a case with vmware about performance of a w2k8 r2 vm. Vmware support made the following statement. "first, the power usage on the vm CPUs seem to stay consistently at the 1064GHz range. The host you're using has the followi...