i have an UCS system running ver 1.4have a server port configured but that shows up as trunk. it should be fabric.have i done some wrong configuration ?how do i change it
i have an UCS system running ver 1.4have a server port configured but that shows up as trunk. it should be fabric.have i done some wrong configuration ?how do i change it
Hi,I am using the UCS Emulator v1.3 and I cannot find a way to connect to the ESX host that comes pre-installed with it. Also the v1.4 Emulator is stuck on "Starting Cisco UCSPE & UCS Manager: 203%" and increasing...Any help would be appreciatedRegar...
Group,Can someone explain how VM-FEX works and specially the limitations you have when implementing it with the UCS 61xx or the UCS 62xx?for example how many Virtual machines you can create in each B230 blade host that can use VM-FEX?Thanks
Hi All,We have just bought a new Cisco UCS C210 M2 product for our CUCM migration to Virtual Machines. We have plugged an HP Monitor and a USB keyboard to start work with the UCS. Then we plugged the server to the power socket and power up the server...
Hi,I read some where on the dcoumentation that A stand alone Cisco server like c210, c250 can be attached to the UCS fabric Interconnect. Can some cisco expert throw some light into it? My understanding is,I will have to connect the UCS FI to a exter...
Anyone have any input, experience or thoughts regarding running vCenter as a VM, on UCS/vSphere 5, where the vCenter instance is used as the integration point for UCSM, and the VM on which vCenter is running is connected to the vDistributed Switch (h...
Have been hacking at this a while and not getting Appliance ports to work. It appears that Appliance ports cannot be used in a PIN group? Also the VLAN's made under the "Appliances" tab are only seen by Appliance Ports. But the VLAN's under Appliance...
Hi I have a UCS C210M2 with 4 GB RAM and 5620 processor and LSI 9261-8i RAID card.It was working fine till I decided to upgrade the CIMC from 1.1 to 1.2 from the CIMC itself using the 'Install CIMC firmware through Browser Client'The process got stuc...
Hello Everyone,I'm new to the UCS solution and I recently tried to update CIMC and BIOS via the Host Update Utility. There were some version warnings that prevented the upgrade, but I was able to update the NIC firmware.CIMC is at version 1.0.2 and B...
Hi, I have a setup which requires installtion of VMware ESX on a RAID configuration of 1 + 0. I currently have Cisco UCS M1 C200 with LSI MegaRAID adapters, i also have 4 physical disks(500 Gb each) which i have configured for RAID 10, the resulta...
UCSM 2.01q with 6120XPI can create port-profile using . (dot) for example "VLAN30-192.168.1" but it cause some warning message (picture below)so I try to change the name to VLAN30-192-168-1 it can work just finemy question is Can I use . (dot) in my ...
Hi, Cisco:I have heard a lot of horror stories after UPGRADING to Cisco UCS 2.#(##).My customer is running 1.4(2B) and I have to perform an upgrade, so I am pondering SHOULD I upgrade to 1.4(3#) or 2.#(##). It is a production environment. SAN Booting...
We just upgraded from 1.4 to 2.0. When we attempt to login via the GUI the ssl cert that is issued is expired, this does not allow us to login. How do we deltele the expired cert and create a new one?
Hi,Some how i got the feeling that to an Appliance port only a iSCSI target can be connected. I may be wrong. If i am i want the experts to clarify. To me it appears that, UCS FI, can not work as FCF that Nexux 5000 is capable of. If it is not capabl...
How do you test the call home feature on Cisco Call home?Thx
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-06-2024 10:53 PM | ||
10-03-2024 07:41 PM | ||
10-03-2024 07:39 PM | ||
08-15-2024 11:16 AM | ||
08-15-2024 08:03 AM |