Voice Systems and Accessories - Small Business

Hello Friends, Please excuse the naivete, but I'm a little new to this device.So, first question, I want to make sure I understand the device.Phone (or FXS port) provides a dialtone to a normal phone.Line (or FXO aka PSTN) is meant to connect to a Te...

Have an installation with a UC320W and 8 phones (most are SPA504G).  This has been in place for one year and the infrastrucuture is new with separate CAT6 cabling for the voice network.  On two occasions we have lost the ability to make intercom call...

HiI have two DECT phones and three iphones connected to a 3CX server. When I try to transfer the call from the iphone to the cisco all is ok, but from the cisco to any other phone, it fails.I selected on the page just one line per phone.Am I missing ...

Hi all,I have an CME with 8.5 release and I inserted an VIC2 - 4FXO.I configured the FXO Port as below:voice-port 0/0/0 trunk-group ALL_COT supervisory disconnect dualtone pre-connect cptone PT timeouts initial 5 timeouts interdigit 7 connection plar...

We're looking at the UC540 and want to use wireless headsets that are not bluetooth. We don't want lifters, so I only want to look at phones that have electronic hookswitch built in. I see that the SPA525G and SPA525G2 has electronic hoookswitch, but...

Hi, I need some info please on how to setup the Wan port.  Here is my setup:  I have 2 locations and 2 UC560.  What I would like to do is beeing able to use one IP on the Wan port in the same subnet as the vlan1 ip address so that I can keep my voice...

HelloI recently bought and successfully configured a Cisco UC320W to my small office, and everything's doing well, apart from the SIP account that I intended to use, with Voipbuster.When I configured the gateway, the SIP account showed up as being re...

Quoting BE3K with 881 CUBE using SIP as the PSTN connection. Customer requires an analog station port for the fax machine. This is a competitive deal agains ShoreTel. I can't afford to add a VG224 to the solution. What other options are available? Wi...

Hi I hope someone can help. We have installed a new uc320 for a customer in london, its running the newest firmware but the customer is reporting a lot of line noise. We have only heard this once but the customer is adamant that they can hear a hum o...

Hi there,I have a CME system with UC540 and a number of SPA509G phones. The reception phone has several extension numbers associated with it and I'd like to select one extension number to appear as Caller-ID.How to configure one specific extension nu...

                   Добрый день.Работает связка be3000 (8.4) + spa8800 FXO (6.1.7) для входящих городских вызовов. Клиент хочет АОН.  Со стороны МГТС могут выставить Caller ID как FSK или DTMF. В обоих случаях при всех вариантах настроек SPA:Caller ID...

I have two UC540 running latest firmware setup as multisite. From one site to another site we need to use a scan to email feature, that uses SMTP port 25.But the UC at HQ is blocking it. I'm able to ping it, not sure what the issue is? any ideas?

Hi,I want to know about the followings support,Firstly, does UC 540 support CME 8.6? if yes then is it support SPA 500 series phones? if yes then can UC-540 register these phones over WAN using SSL vpn tunnels?Second, does cisco jabber in iPhone supp...

I'm looking to configure fax detect on the UC 520.I can get listen-first to work for faxes only. After 9 seconds, or when I press any key...the call is disconnected.If I confgure it for connect-first, the line just rings... never answers.Config is at...