Hi there - I'm working off a CISCO IP Phone 303 and can't seem to change the Hold Music - anyone know how we can do this? Much appreciated! Georgie.
Hi there - I'm working off a CISCO IP Phone 303 and can't seem to change the Hold Music - anyone know how we can do this? Much appreciated! Georgie.
I have this phone spa525G2 at first i was able to access the web gui but i could not change any configuration when ever i could go to admin login it was requesting for user name and password which i did not have so i decided to do a reset on startu...
Hey guys ! When I configure all access with "any" "any" on ASA 5506-X firewall on packet tracer, access with different protocols is perfect. But once I do advance configuration by allowing protocol access to specific hosts or subnets, no single acces...
We have a customer that currently switched to VOIP phones. There old phone (Panasonic TDR100) system had a intercom and receptionist phone that had that triggered the door lock release. I hooked up the ATA and removed the 4 wires going to the PBX tha...
Hi, I have never used Cisco equipment and sourced a second hand ATA 192 unit for VOIP. I attached it to the domestic router using the network port. ATA was hardware reset with a paper clip. I rang the unit on the analogue phone **** 1110# and it repo...
1. DHCP is working and provides IP addresses for everything else connected2. the voice modem has been rebooted and reset both -- twice3. ***** 112# says the IP address is 0.0.0.04. I've tried reserving an address for the MAC address, no go either but...
Hello.SPA 112 didn't accept network parameters when used IVR for Administration.When I filled in parameters using IVR menu, then SPA 112 rebooted and not accepted setting.Maybe I must use some instructions, which were not wrote in administration guid...
Hi,I am trying to confiqure my SPA112 using the default ip address of 192.168.15.1 however it doesnt seem to point me to the admin panel.When I phone the IVR to check the IP address it gives me 0.0.0.0 and no matter how many times I try to change it ...
I recently moved my landline over to VOIP and the SPA112 has so far worked well. One thing I noticed is that even if I dial local numbers, I still have to add the national prefix, e.g. so for dialling 828171 I have to type in 01455 828171. Is it poss...
Hi,We have an ATA191 MPP we bought on Amazon (supposingly new) that is already locked to a voip provider. We can do a factory reset on it no problem, and do the setup config for our own needs (Freephoneline), but the minute we reconnect it on line, i...
I'm trying to upload a custom ringtone to my desk phone and keep getting an error after it asks me to select a slot to save to saying "invalid file format"It does the same thing if I press play, and also if I add it to the MP3 player playlist then tr...
We have many Cisco SPA502G VOIP phones that are no longer in contract and have the original firmware installed. We are now years behind and I would like to update them. I have downloaded the firmware. I have a .bin file I have no idea what to do w...
When trying to add an additonal extension on a clerks 8841 phone that belongs to his supervisor I get this message...I remove an Item but still not able to add the new line. Any help on this is appreciated.
Hi everyone i'm having issues with caller ID here in mexico, my telephone provider is Telmex and i can figure out the way to get the called Id working. Can you help me with this? I have selected european Fsk in the spa400 and in some calls the caller...
HelloFor a short time now, my LTE connection in the Cisco router has been breaking down repeatedly. This is very annoying because the VPN tunnel used is always gone. Unfortunately I can't do much with the logging messages. these messages are shown af...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: