Hello: We are starting to get more and more SIP Vicious scans. Today, we received a scan and now when some (but not all) of our phones dial extension 100, instead of "To: 100" we see "To: sipvicious".I understand most SIPV scans are attempts to enum...
Forum Posts
Hi there, I loose the web GUI access to a CP-7821 3PCC, I just reset it but all I can get is:Before the reset I was able to access the WebGUI but the credentials won't able to let me in.Thanks for help. Guillaume
Hi supportWe are a danish ISP who use Linksys RTP300 and WRP400 routers as CPE equitment. Trough our Danish Cisco contact (Henrik Bønnelycke) we have been told to discuss our prolems with the WRP400 router here.Our problem is that the router seems qu...
I am using a Cisco SPA122 ATA I have an intercom phone that dials my SIP phone number. When I press 5 to allow entry, the door does not unlock. I have tested with my friend, had him call me, when I press 5, my friend does not hear the tone. When I ca...
Hi,I have a modem with IINet (VX420-G2h (AX5400) with a ATA112 connected.I have connected a phone to Line 1 of the ATA. The configuration of Line 1 is attached.I can make calls form the phone fine but I can't receive calls.It would be appreciated if ...
Hi everyoneI am trying to reboot remotely a CISCO uc540w-bri-k9. On the interface, it says "uptime is 1 year, 4 days, 3 hours, 43 minutes", when I use the command "show version", that is why I want to reboot it. I tried commands "restart" and "reload...
I acquired two used SPA504G. All display labels were in Dutch. Because they were used phones, I reset them to factory default. Now all labels are in English. Are there any public domain dictionary servers I could access for the Dutch language labels?...
Hello,I did factory reset device phone Adapter with Router model SPA2102-R. And then I tried to bring up web management by dial 7932, but it's asking for password.I am wondering what is default password after factory reset. Please help to advice Brs,...
Hi folks,I have a 7926G SCCP community with a 2911 running CME v9.4 trying to talk to a new 7841 SIP community with a 4331 running CME v14.1.Skinny phones can talk to skinnys, SIPs can talk to SIPs. How do I get them to interwork, please?Andy
Dear all,I have an SPA112 which I would like to use in the following scenario:Multiple phones connected (can be to one port using splitters), two SIP providers configuredIncoming calls coming through provider1 should ring all connected phones (no inc...
We have a Cisco SPA 112 ATA connected to a Broadsoft hosted phone system.FW 1.4.1 SR5The ATA has a Hosiden Besson Bedlam Loud Tonecaller bell connected.The hunt group phones ring including the bell, the call is answered on the phone but the bell cont...
Was trying to switch versions from active 11.6.1.10000-51 to 12.5.1.10000-31 fails at 'Checking Pre-requistes' step with message: "ERROR: Switch version cannot be performed as SSH passwordless connection is not setup correctly between the two nodesSw...
Hello everybody,so Im pretty noobish when it comes to this topic so please bare with me.My dad recently bought a CISCO ATA 192 in order to integrate our analogue doorbell / speaker system into our IP phone system.so the bell has a momentary switch wh...
HelloFor a short time now, my LTE connection in the Cisco router has been breaking down repeatedly. This is very annoying because the VPN tunnel used is always gone. Unfortunately I can't do much with the logging messages. these messages are shown af...
I manage several facilities that utilize one CP-8845 and one analog cordless phone plugged in behind an ATA-192. I have seen the data sheets on how to transfer calls FROM the analog device, but my question is: if a call is answered on the CP-8845, an...
