VPN

Dear All,There is a requirement of one Remote Access Server (RAS) from the customer where we are quoting Cisco 2610XM Ruter as RAS. My question is to make this router as RAS, do we need to have IOS of Remote Access Server (Cisco 2600 Ser IOS REMOTE A...

Hello allI have purchased a SOHO96 from my ISP and have configured it fine, but i cannot activate the VPN component via the CRWS, is this possible. the error message that i receive is " this feature is not supported on your router" My IOS is (SOHO96...

hello,I have a problem about VPN connection between Checkpoint R55 and Cisco. Configuring an IPSEC Tunnel between a Cisco Router and NG is documented on Document ID 23784.But in this example, both networks inside gateways are private. Unfortunately, ...

I have found the document of configuration on the concentrator 3000 web page but the VPN tunnel does not establish.Getting the error messages :%CRYPTO-6-IKMP_MODE_FAILURE: Processing of Informational mode failed with peer at x.x.x.x (concentrator)ISA...

Hi,on a Macintosh powerbook machine I got some problems with using MS X.509 certificates.Although I could positive manually verify certificate chain the client states that it could not load private key:1 10:13:13.045 02/08/2005 Sev=Info/4 CERT...

HiI was striving arround through the new PIX Command Reference and CLI Guide, but didn't find an answer to my question:Since there are a lot of new VPN features in the new OS Version I was wondering, whether the feature "allow local LAN" will be supp...

One tunnel endpoint (10.7.7.7) doesn't come up (PIX 501). IKE Phase 1 fails. <#debug crypto isakmp> on 1700 (which is a hub with VPN accelerator card, and connected to 10 other tunnel endpoins) show following:01:25:53: ISAKMP (0:90): deleting node 14...

Hi,I have configured VPN in my PIX515E. Everything is working fine. The only thing is that my VPN client can't reach the DMZ. Any suggestion? Thanks.Andrew

Hello.We've got a 1721 utilizing ISDN Dial Backup (BRI0). Here is the BRI0 config:interface BRI0 description ISDN Dial Backup ip address negotiated ip nat outside ip hello-interval eigrp 100 3 ip hold-time eigrp 100 9 encapsulation ppp dialer map ip ...

I have two sites connected through IPSec VPN tunnel. Each site's PIX has number of interfaces and the same VPN tunnel is used to allow network traffic between the different interfaces. This set up has been working just fine for an extended period of ...

I've got two pixes with a site-to-site shared secret ipsec vpn set up and working.I'm now adding a third site, and wished to create a second tunnel on each of the existing pixes to the third pix.I THINK it's just as easy as adding a new peer and acce...

My worksite installed the Cisco VPN Client 4.0.3(A) on my ibm thinkpad running Windows 2000 (5.00.2195) Service Pack 4. At home, we have a home network through our DSL line. The main computer is running Windows XP SP2 with internet connection shari...

Hello,We have a 3825 router at a remote facility with one Internet T-1 connected to it. The 3825 has multiple site-to-site vpn's running over the T-1, but now we also need to configure EasyVPN so that our Engineers can vpn into the remote site (to ma...

If I want to have multiple remote peers to have ipsec tunnels to central site (one peer one tunnel), what device must I have on central site? Can I use 7200 router? PIX? Or concentrator?thanks!

Hi. I have a PIX 515 that has several working VPN Connections to it. We are trying to get a SonicWall to connect but we are having problems. However, I don't think that the problem has anything to do withthe SonicWall itself -- I don't think we're...