My Air-cap1702i access point will not join WLC right away after upgrade firmware from 153-3.JA3 to 153-3.JI5 WLC AIR-CT2504-K9 Software Version 8.0.115.0Reason For Last Unsuccessful "Attempt Join message decode wtp ipv4 address Failed" Log from AP*Au...
Forum Posts
HI, I am using cisco virtual wireless controller version 8.3.143.0 with access point 2700 series. We migrated WAPs to a new vWLC with same configurations. However, after joining the new controller when client tries to connect to PSK based SSID its pa...
Hi! We are going to upgrade our WLC 5508 with 2702i APs from release 8.3.141 to release 8.5.140 In the release notes there was information regarding "WLAN Poller", se below link:https://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-la...
Hello I'm writing here because I can't find a clear solution to the WI FI configuration of this product,I don't know if I can publish the commands I use to enter the WI FI unit as "sh platform"Chassis type: C1111-8PLTEEAWE Slot Type State Insert ti...
Good day.We have WLC 2504-15-K9 with pre-installed liecense for 15 APs Now we need to increase number of supported APs up to 40. So what type of liecense should we bought for this solution ? And whats the steps of liecense instalation on the WLC in t...
Hi to all, I'm using C3702e (40Mhz) and 1852e (80Mhz) Cisco Wireless controller.1852 was bought last week, unfortunatelly, i'm not able to reach 80Mhz with it... only a poor 40mhz (300Mbps download/ 450Mbps upload).Performance of my 1852e is pretty s...
Hello, Are Cisco 9117 AP compatible with Cisco 3750-X switches. Both supports 802.at POE+ but main question is 9117 is Multigigabit Ethernet port, whereas 3750-X are normal Gigabit ports, will it cause any issue or work fine with limited capabilities...
Hi, I am new to Wireless networks and a I have some clarifications. I have a scenario wherein my client needs to upgrade to a new WLC 5520. They have a two sets of 5508 WLC. One pair is configured for HQ office and another pair is for Remote Site...
I have an AP joined to a Cisco WLC 2504 controller. I'm running a few debug commands on the AP directly, but the idle timeout period is way too short. Is there a way to change the SSH idle timeout either temporarily or permanently on the AP?
Hi All, Could you please help me to resolve this issue. These phones are stuck in DHCP REQD stage on Foreign controller but having Ip address in Mobility anchor controller.only below message is getting in logs. Also I could see the log on Cisco ISE ...
Hi there,I try to delete some old APs which are moved to another WLC/Prime world or just the WLC was removed. I'm not sure what my colleauges did in Detail. But when I do it, the AP stay in the prime without an error message.The AP is not Associated ...
I am trying to setup evaluation licenses on a Catalyst 9800-CL appliance. I was told all you have to do was registered it under your Cisco smart account, and it will automatically activate the evaluation licenses for the appliance under your account....
Hello. Have IW3702-2E with x4 AIR-ANT2568VG-N 2.5/5.0Ghz 6/8 dBi Omni antennas.AP is in autonomous mode ap3g2-k9w7-tar.153-3.JI4.tar. I have run several copy test`s;2.4ghz I can connect 144Mbit only, cause there is only 20Mhz mode available, and real...
Resolved! LAN isolation
Hi all,I am new with Meraki and I have some doubts how to configure two SSIDs in the office. I have one SSID CORP in Bridge mode using DHCP server and I have Guest SSID in NAT mode. I want Guest to not be able to reach Corp network but because NAT mo...
Hello everybody,I have an issue where the captive portale won"t work properly, the problem is that I have control over the WLC only and not adipsys platform I think I did what should be done in the WLC following the official guide provided by adipsys...
