Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
I was looking into Radius profiling on the WLAN controller. I would like to make the recommendation that DHCP should not have to be required in order to do profiling. I understand that DHCP is required to actually profile. However, it would not be ne...
Hello guysi have 5508 controller in HQ , i like to install wireless network at branches, i have 3802 AP , any recommendations about ? , any specific configuration on Router of branch that will be come in the front of AP ?regards
Resolved! WLC License Transfer
regards I have 2 controllersThe first has 15 licenses WLC CISCO 2504The second i purchased has 12 licenses. WLC CISCO 5508And i have 13 APs installed on my site.I would not use the first controller due to device failure.How can i move 15 APs license ...
HiI received a Demo-Kit with an MR33 Access Point - which was installed really simple and fast.We are using a local Windows DHCP server why we set the AP into bridge mode with dot1x authentication.Authentication is successful and now the problem begi...
When I restart Aironet 2802i that's powered by SG300-28PP 28-Port Gigabit PoE+ switch, I see the following message: [*09/26/2016 13:47:31.8044] Radio0 not started, not enough POE power [*09/26/2016 13:47:31.8173] DOT11_DRV[0]: set_channel Channel set...
Just wondering what Cisco's recommendation on this is. Also, can I take a backup of all my settings on an earlier software version and import them on a later software version?
PI 3.6WLC 5520, OS: 8.5.151.0 what does this mean?env_monitor.c:101 Check sensor fail: Octeon Temperature, errno 11, errstring Resource temporarily unavailable.I found it PI system log viewer thank you.
I've been trying to configure Cisco Mobility Express on Cisco 3802i. However could anyone please advise why I am not getting 'VLAN' option in below screenshot. Any advise would be highly appreciated. Thank you
Hello Experts, Its understood that the telecom licensed frequency is completely different from the unlicensed frequency spectrum the Wi-Fi uses.However I find it difficult to find what specific frequency bands the 5G standard will be ratified for usa...
Greetings,I just inherited a small Cisco Aironet wireless network and I am still kinda lost with the different models.Network is REALLY small, was just two AIR-AP1832I-E-K9C with Cisco Mobility Express running on one of them. Unfortunately the second...
In all Cisco documentation, I've seen FlexConnect referred to as a per-AP feature (instead of per WLAN). Can I have an AP serve both WLANs that have the "FlexConnect Local Switching" on and off (under the Advanced tab)? I'm using a Cisco WLC 2504 con...
This document shows how to enable / disable sticky key caching (SKC). How do you enable / disable opportunistic key caching (OKC)?
Resolved! NTP broken on WLC 2405
Hi, I have noticed that a WLC 2504 that I have appears to have problems loading an NTP server. Whenever the system boots up, or is attempted to configure a time server, the console errors out with the following logs: /usr/bin/ntpd: error while loadin...
Hello gurus, I have a situation that I do not believe I am the only one in the universe who wants a solution like this. But still I can't find any answer to my question. I have a pretty standard topology with some central datacenters and remote branc...
Hello i have multiple 2802i AP running Mobility Express image. Primary 2802I is working and controller is running off that perfectly but the second 2802i AP which was converted over to ME has also joined the Controller but no under ME AP i see no cl...
