Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
I've just established etherchannel between 2802 AP and C2960S switch.Which of such supported load-balancing modes can allow traffic balancing between two LAN ports connecting access point: (config)# port-channel load-balance ?dst-ip Dst IP Addrdst-ma...
Hello Cisco community, I have two WAP531 at work (one in the office, one in the warehouse) and they are working both in a cluster (Single Point Setup). They diffuse the same SSID and Roaming is working fine.Now for security reasons I just build a Rad...
Hello guys, I have a question and I would like someone to give me visibility on how the management gateway failover works.What would be the normal behavior of having this feature enabled or disabled for a Wireless network with HA SSO?.The Cisco docum...
good dayI have a client who reports the following vulnerability in the WLC cisco:The server accepts connections using SSL 2.0, SSL 3.0, TLS 1.0 and / or TLS 1.1. These versions contain many cryptographic weaknesses and are considered obsolete by the ...
Resolved! 1852i and Guest Anchor Questions
Good morning! First off, a quick question on the 1852i. I noticed that when comparing the AP models, the 1850 series is not listed anymore. Is this an error or is the 1852 on its way out? https://www.cisco.com/c/en/us/products/wireless/access-point...
Hello All, I deployed a wireless network on AIR-AP1832I-R-K9, firmware version 8.7.102.0, in the mode Mobility Express.When users log on, they go to the internal authentication page to enter their login and password.What certificate should be used fo...
I want to configure a new AP 1572IC1-A-k9, but I can´t turn on the AP, I connect the AP with a AIR-PWRINJ1500-2=, but when I connect the AP to the power injector port with a ethernet cable the AP is not turnning onThe AP has the next specification:80...
Resolved! Slow Web GUI WLC 5520
Hi im having trouble with WLC GUI web page very SLOW?
please help us to find proper Cisco wireless product with following requirements : 5.8 Ghz, 2-3 miles, 2-4 Mbps. Thank you very much.
Resolved! AP Placement Orientation
Have a client with a few locations, each with over 15K sq ft and with 20' tall ceilings. I've been installing the MR-18s and MR-32s on walls, about 12' up from the floor, using the included wall plate. Should I have been installing face down from the...
Hi All,Currently i have doing project cisco wireless controller in customer, we used WLC 5520 series. I have tried to setup ip address etc, but when i try to access (browse) it look not like wireless controller, it show cisco integrated management co...
Resolved! Upgrade Cisco 5508
Hi All,I am planning to upgrade Cisco WLC 5508 which is currently having Software version 7.5.103.1 and Field recovery software version 7.6.95.16. Latest available software for this device is 8.0.152.0 (AIR-CT5500-K9-8-0-152-0.aes).Is it recommended ...
We have several 5520 WLC....they have smart license tokens and are registered on the portal....we have two types of license in the virtual account for WLC......AIR-DNA-E-T (few hundred of these) and LIC-CT5520-1A (13 of these)......when a WLC checks ...
I am having a problem with lap's getting updated firmware from the WLC. I currently have the WLC on say management vlan 99 and the APs are on a separate vlan (we will call this vlan 100). The switch port for the AP is configured as an access port for...
Resolved! 2 SSIDS, 2 Gateways
Further to this posthttps://community.meraki.com/t5/Wireless-LAN/DHCP-Issue-on-2-SSID-wireless-network-with-2-different-gateways/td-p/42710/jump-to/first-unread-messageSo on the switch I set the follwoingPort 1 to native VLAN 1 and only allows VLAN 1...
