Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

Hi Everyone, I need a little bit of verification based on facts; I am aware that Cisco APs designated for my region (Nigeria) are the AIR-CAP3702I-E-K9 model APs. I want to find out if the model AIR-CAP3702I-A-K9 can be used here also. Cisco does not...

vezeh by • Frequent Visitor
  • 2942 Views
  • 6 replies
  • 0 Helpful votes

When I go to the below path I do not see any devices (which I have +900 WLCs managed), associated to any profiles.   Step 1 Choose Inventory > Device Management > Credential Profiles . Step 2 Choose a credential profile, then click Edit .   Looking f...

ROB ADAMS by • Level 3
  • 1328 Views
  • 1 replies
  • 0 Helpful votes

I have current wireless infrastructure with cisco 3600 and 2700 APs and would like to set one 1602 AP to be mesh or repeater so it can be mobile. currently it's getting an error message of non WPAv2 PSK.   Do I need to set one AP to be a Root AP and ...

leej48 by • Level 3
  • 7906 Views
  • 24 replies
  • 0 Helpful votes

Product/Model Number : AIR-CAP3702I-E-K9System Image: ap3g2-k9w7-xx.153-3.JCAP Location: EU Hi,I am working with 5 GHz and would like to set AP to use one of the following channels (as other channels are experiencing Wi-Fi saturation. 120, 149 , 183B...

amh4y0001 by • Level 5
  • 9874 Views
  • 7 replies
  • 0 Helpful votes

Currently working with Cisco 1552s Access Points in a production environment. These APs are being used to monitor sensors in the production environment for safety monitoring. I have been searching for information on how many sensors one of these APs ...

kolive1001 by • Community Member
  • 1264 Views
  • 3 replies
  • 0 Helpful votes

Hi Anchor WLC 5508 - 8.5.134.0 Foreign WLC 8500 - 8.0.152.0    I'm not new to this, been creating Mobility Anchors for years, but I've not seen this issue before, specially when was working.   I've got 1 Anchor on DMZ behind a Palo Alto FW. 3 Foreign...

what does [None WPAv2 PSK] error message mean?   parent lost: received disassociate (1) failure associated to AP_MAC and then [None WPAv2 PSK]   it repeats and repeats.   What could be the issue here?

leej48 by • Level 3
  • 936 Views
  • 1 replies
  • 0 Helpful votes

I have configured 1602 as bridge and other APs are at local right now. I have to change AP from local mode to bridge in order bridge AP to work, correct?   Below is the show logg from the AP   8 00:58:17.031: %DOT11-4-CANT_ASSOC: Interface Dot11Radio...

leej48 by • Level 3
  • 1138 Views
  • 0 replies
  • 0 Helpful votes

I wanted to reach out to the community and ask if anyone has run into any bugs or issues when upgrading Cisco ISE 2.2 to Cisco 2.3 or 2.4?  This is specifically with wireless since the environment i'm working in is currently running 2.2.  Any land mi...

Hi ,    I am setting up a new vWLC in VMware. 1. why data port should be trunk? what it is used for ? 2. I already have a vwlc in production how to find the data port ( ip address ) of that vWlc ? 3. Difference between management port , service port ...

KM2018 by • Level 1
  • 1073 Views
  • 1 replies
  • 0 Helpful votes

HiI have a cisco wireless AP AIR-LAP1242G-E-K9When I plug the network cable into the back this lights come on and change colour.Does anyone know what the lights mean when they change colour?ThanksRegards

Hi All,I have a 3702i AP and I cannot get wireless clients to connect to the 5GHz channel no matter what I do. I read a couple postings back in 2014 and 2015 and someone said the autonomous software is for site survey only which means 5GHz cannot be ...

Em87 by • Community Member
  • 7075 Views
  • 14 replies
  • 0 Helpful votes

Hi,   I am trying to integrate my Cisco Prime with ACS. but its not successful. I just followed steps from the below cisco document.- "Use Cisco ACS With RADIUS or TACACS+ for External Authentication" https://www.cisco.com/c/en/us/td/docs/net_mgmt/pr...

Review Cisco Networking for a $25 gift card