Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello. I just purchased anew hwic ap from eBay and have already installed it into my 3800 router in hwic0. I don't know where to go in the console to configure the device or to even check if the device is detected. I have never inserted a modu...
i have a employee who is requesting to have two access points in his office which are connected to the same WLC , wouldn't that actually have negative impact on wireless performance for him in the room or not?
I am working remotely on a new install of MSE 8.0.130.0. The initial setup apparently did not activate it so the only access I have is via Putty. I am not a Linux guy so can someone tell me the CLI command to turn on HTTPS so I can get to the dashboa...
I recently upgraded the software of our WLC 5508 from v7.4.121.0 to v8.0.121.0 and after I applied the upgrade to WLC, I pre-download the software to all APs including FlexConnect APs, I noticed that other Flex APs were able to download the software ...
Is there any command to find the Native Vlan (configured under FlexConnect tab) of ALL access points in WLC? I have a Flex7500 and running code 8.0.120.0 Thanks, Mehdi
Hello, after updating our WLC 7500 from version 8.0.100 to 8.2.100.0 funkioniert the VLAN mapping on the APs no longer reliable. This means that the client can authenticate the AP, then get an IP address from the DHCP server associated values. If we...
Hi all, Question regarding remote anchor WLC redundancy functionality. Topology: 2 locations, each with anchor WLC. Location 1 is primary anchor (priority 1), Location 2 is secondary anchor (priority 2). How would (if at all) fail over work, if ...
Resolved! Radius and PSK on a WC5508
Is it possible to get a WLAN on a 5508 to work with both a WPA2/PSK and Radius? I am trying to set up a WLAN that has some reasonable level of access control (hence the PSK) but is only accessible by certain machines (hence Radius and MAC filtering)...
Hello, This is regarding Access point integration with WLC 5508. Post downloading the software image from WLC Access points will be configured as per the production environment; however we are observing that the Access points (1620i) by default are ...
Hi buddies, We've deployed a wireless network with WLC 5508 and aireos 8.0.120 for a high density multi floor building. but there are issues like below: 1. In spite of nearby APs hearing themselves really good, WLC choose same channels for them. Is c...
Resolved! Netflow in WLC
Hi, Can anyone shed some more light on the two different record types on the WLC? Im running a ipv4_client_app_flow_record-type now, and its working fine in CPI - but would the src-dst-ip give me more/less? Could i see what hosts each client is talk...
Dear all can any body help me. i have to block lan access to guest user.. but guest id and whole internal network are in same subnet. suppose 10.10.X.X guest ip is 10.10.202.X can any one help me .. when i try icmp, inbond ourbound all any any its b...
How to enable 2.4G HT40 on Cisco 2702? Does any images can enable 2.4G HT40 on Cisco 2702? I would like to use 2.4G HT40 to test wifi throughput, Thanks a lot.
Resolved! Cisco WLC 4402-25.K9
Hello community! Does anybody know if the “Cisco WLC 4402-25-K9” Wireless Controller supports the "Cisco AIR-LAP1142N-A-K9" Access Points? If I buy this controller secondhand, are there any licenses to pay per month or year? Thanks!
Hello, I am experiencing difficulty with a router entering into dot11radio0. It is an 881 w ISR with a Cisco IOS version 15.1. when I enter this command I get an invalid syntax message. I am new at configuring wireless, and am not sure of what I am d...
