Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hello,I have got WLC 5508 located at main campus and I would like to extend WiFi Connectivity to the new building. I don't want to use Fiber and install a switch along with APs, is there a way I can I have a AP act like a Microwave Dish and at the ot...
Resolved! Adding AP to WLC
Hi Everyone, I need to add 2 AP's to the WLC.Need to confirm only 3 things needed on AP 's configuration:IP address,Subnet mask and default gateway RegardsMahesh
Hello everybody, I have a question regading to the compatibility of the Cisco Catalyst 3650 version 03.07.01.E with the Aironet 2700i device. In the compatibility matrix it shown that the properly version is 15.3.3 JNB but there is not this software ...
Hello, We replace old Cisco AP (12xx) with new Cisco AP 3702. All clients and smartphones work normally except Lumia 830 and Lumia 1520 where we notice connectivity problem. On the other hand Lumia 820 works and connect normally. We try to change so...
Resolved! Crach HA WLC 5508
Hello,I have a problem with my 5508 WLC software Version 8.0.115 in High Availability ModeMy WLC loses its connection and once the connection is restored the HA is down.Redundancy State = Non Redundant (Cisco Controller) >show redundancy summary ...
Resolved! Wildcard or Regex in Rogue AP Rules
I am searching for a solution to automatically classify RogueAPs starting with a known string as friendly.I.e. all SSID is starting with TEST (i.e. TESTn3Tw0rk) should be classified as friendly.I already tried to setup a Rogue-AP-Policy containing Us...
Hi guys,Bit of an issue accessing the GUI of a 2504 sat behind a router.I have configured the management interface nat-address to the public address of the router, and configured a static rule on the router itself:ip nat inside source static tcp 192....
Hello my name is Ivan have a questionI have to make a deployment in high density in environments of 1200mt2, with six outdoor access point 1552, without use mesh technology. We conducted site surveys to work services data, voice and video, and I wo...
Trying to convert standalone AP to controller AP. Not able to upgrade the flash file,Exisiting IOS : Flash:/c1250-k9w7-mx . 124-25d.JA2New IOS : Flash:/c1250-k9w8-mx . 153-3.JA1 (present we are using these IOS to upgrade)We are not able to up...
Resolved! Can Prime be installed on Hyper-V?
I see all these configuration guides to install Prime on VMWare. Is it possible to install it on Hyper-V?
Resolved! N+1 redunday licence requirement..
Hi, I have 2 wlc runing in SSO HA mode. I want to migrate the second WLC to N+1 mode, Do i need to purchase 50 ap count license to the secondary WLC to support ap while configuring N+1 mode. My model is Cisco 5508Regards,JJubair.S
Hi All:i have CISCO AIR-CAP1702I-E-K9 when i finish all the configuration on the WLC (WLC 2504)and everything is okay i have issues in coverage range the wireless range is so bad . i try to install D-Link access point with 4 dBi, actually the D-lin...
Resolved! 3850 SSID ISSUE
HiI have a problem with my WLC inside de 3850 switch. I created 2 SSIDs mapped with vlan correspondient but when the final clients wants to associated with the AP, they Can`t. I have a DHCP server in the same switch but they cant obtain a IP Address....
How to monitor STANDBY HOT WLC when WLC are in High availability . Local StatePeer StateUnitUnit IdRedundancy StateMaintenance Mode
Hi Guys,Can anyone advice me what are the AP models that support Cisco 4400 Wireless Controller .Controller: - 4400 SeriesModel: - 4404Software Version - : 7.0.250.0 Satheesh
