Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Hi, I have some question about AVC on WLC. When I access to AVC status page on WLC, I can see [Application last 90 sec usage] and [Application cumulative usage]. What does this " cumulative usage " mean? Is it mean usage since WLC last reboot? Also,...
I have two SSIDs created in my cisco 1040 AP. GUEST - VLAN 12 WPA2 with pre shared key VLAN 12 with ciper AES CCMP OFFICE - VLAN 1 WPA2 with pre shared key VLAN 1 with ciper AES CCMP But when I tried to create another SSID (Voice SSID for cisco 7...
Hi Guys, I was wondering if someone can offer some advice regarding the selection of the correct type of AP for Voice over Wireless LAN deployments. We are looking to install Cisco 7925G VoWLAN phones, how ever it is not clear for me if we can use th...
Hi buddies, I want to do wireless planning with cisco prime infrastructure. I choose AP 2702-ٍٍٍٍE with ANT-2544 as my desired AP. because it's a omni directional antenna the azimuth parameter is meaningless to set but I dont understand what the E pl...
I am trying to have a management user authenticate via radius and have full admin privileges.For a WCS I can simply set the radius attribute of "Cisco-AVPair.attr|Wireless-WCS:role0=Admin" and that user will get full admin rights. I found this doc to...
Hi everyone I need solution about auto generation login/password for guests in hotel. Can anyone share some experience or advise how do it? All access points are LWAP , registered with WLC 5508 series
Hi All, Can we block andriod/apple ios smart phones via device profiling. As this feature is available in Ruckus. (Device Access Policy)' i need to block Smart phones ios so that only laptop user should connect and they wont able to access their smar...
Hi, I really don't know the pattern of the refresh rate of the rssi of all connected clients. I am using a WLC to access the AIRESPACE-WIRELESS-MIB through SNMPv2 and check the table bsnMobileStationRssiDataTable. But the rssi values registered doesn...
Hi I will like to know how to change the management interface on a WLC, the Netmask is currently a /23 but will like to change to a /22. I noticed that the configuration by default is grayed out when I check the GUI, can I have assistance on best pra...
Hi all, I am trying to set up Prime 3.0 to monitor some HP WX wireless LAN controllers, and don't seem to be having much luck in finding and being able to import MIB;s into Prime. I was wondering if any one else has done something like this or simil...
Hii i am try to convert AIR-AP1041N-E-K9 autonomous to Lightweight (Controller Base). i was successfully upgraded but it can not find the WLC IP. I don't know why it happen. i have also check the switch and found it is fine and DHCP is enable. i have...
This is in Prime Infrastructure 3.0. When I go to the controller configuration and select WLAN Configuration, there's no option to create a new WLAN. I have to go to the controller itself to create it. I thought I could do everything from Prime or am...
I have my CCNA R&S and Collaboration certifications and am thinking of going for the Wireless cert too. Currently I have a few 2811 routers IOS 15, a 3550PoE switch, a 1230 AP and a 1242 AP. I see there is this Prime download that I can get for fr...
Hi, I have 2 models of controller WLC 5508 and 2504. I have 2 groups of APs. WLC 5508 is running version 8.0 and WLC 2504 is running version 7.6. Can I configure to be used anchor between 2 controllers? Now I have no link between 2 controllers but I ...
We have Datalogic brand Falcon X3 hand held wireless scanners. Users drive forklifts rapidly through the warehouse and use the scanners. When we had Cisco 1200 series autonomous access points there were no problems. We just installed all new CAP 2...
