Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi GuysWe are deploying an Anchor Controller (2504) to terminate our Guest SSIDs. We are using new mobility to support a mix of 3850, 5508 and WISM2 controllers. SSID1 (Guest) - Open with Layer3 Web Authentication on Anchor controllerSSID2 (BYOD) - ...
Hi, I have a situation where wireless clients are not able to resolve the Layer 2 address of their default gateway (I can see this via an arp -a command on a wireless client), this is on our guest SSID, the controller sits in the DMZ along with the g...
hello,I have a hardware-failed device Cisco 2106 from which I have the configuration. I have a new 2106 device. Is there a way to move / import / copy the old configuration into the new 2106 ?Thanks PS I have the show run-config commands
I'm running version: 8.0.120.0 and would like to know if there is a way to manually change the hostname without using the setup wizard?
hello,we have a couple of access point Cisco AIR-CAP2602I-E-K9 that are configured as lighweight access point.can we convert these access point to mesh firmware ?We need to configure these access point in Bridge mode as RAP or mesh access points as M...
Hi All,We are facing some weird issue after applied the initial configurations and first reboot in our MSE 7.6. Even we double checked and corrected our NTP settings. Additionally, we disabled the system cryptography to use FIPS. All looks fine, howe...
Hi All,Got the title error when adding an AVC rule to a profile. My device is WLC 2504 on software version 8.1.102. I know the AVC feature is working fie on previous 8.0 software. Do you know if this feature had been removed or this is just a bug in ...
Hello everyone,I'm currently using a 3702E AP in Autonomous Mode for some performance tests and I would like to monitor the following parameters: SNR, RSL and SIR. However, I was enable to find these parameters among the variables provided by the MIB...
Hi allThis maybe a dumb question, when connecting a root ap to a mesh ap, do they use the same channel to connect to each other?cheers
hello everybody, a few months ago Peter (see attached reference) wrote that the new 2700 AP will receive a new Single, Unified Software Image - where apparently this image could be used for Autonomous Mode as well as for Controller Based WLAN communi...
Hi Team, There are alot of AP's from different sites are assocaitig to this controller. I am using flexi connect local switching. In this case while creating the dynamic interfaces lets say for vlan 10 , In ipaddress field " Specifically which Ip add...
Good Morning, I am setting up new Cisco 5508 WLC at Guetamala location. When I try to select Country Code, there is no option for Guetamal, what should I select for Country Code ?Controller Info. AIR-CT5508-K9 AP informationAIR-CAP3702I-A-K9 Than...
I try to do a Lab, using NAT-PAT function in flexconnect AP, let wireless clients can access network by PAT translates client's IP to thin AP's IP. below is my topology:Topology work is well, clients can get private ip per WLAN, and access network ...
Hi,i am using Cisco ISE to automate the Guest user ID creation. Below API works fine for the ID creation but SMS to the user is not automated. However, if do a resend credentials on the sponsor portal then SMS is delivered to the client. SMS Gateway ...
Hi all, I m doing configuration on wlc 2504. But I javesome doubt, I have created 2 ssid. On . Management interface I have configured local IP and I want to configure public IP on another interface. Is this possible that can we configure local DHCP...
